38-116 updated it works!!!!

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

38-116 updated it works!!!!

hotrod
Junior Member

Posts: 32
Threads: 2
Joined: Apr 2010

05-02-2010, 08:28 PM

Oh No, I think my output transformer is bad on the while trying to measure the dc resistance it kept jumping around a little if I move the wires it jumps around a lot and it read rather high. From the center-tap it will read anywhere from 6K to open. The secondary checks out okay at .3 ohm connected to the voice coil but I'm surprised I am getting a reading of only 42 ohms between the primary and secondary. Sound like the primary is shorted to the secondary too me. Anyone know what Universal transformer to get for this as the service literature only gives ohms ready and not impedance information. This output transformer is Philco part number 32-7751.

Thanks
Rod

Find

« Next Oldest | Next Newest »

Messages In This Thread

38-116 updated it works!!!! - by hotrod - 05-01-2010, 03:28 PM

Re: 38-116 IF transformer question - by Ron Ramirez - 05-01-2010, 06:14 PM

Re: 38-116 IF transformer question - by hotrod - 05-01-2010, 07:55 PM

Re: 38-116 IF transformer question - by Ron Ramirez - 05-02-2010, 09:49 AM

Re: 38-116 IF transformer question - by hotrod - 05-02-2010, 06:12 PM

Re: 38-116 IF transformer question - by hotrod - 05-02-2010, 08:28 PM

Re: 38-116 IF transformer (new question Output transformer) - by Ron Ramirez - 05-02-2010, 08:53 PM

Re: 38-116 IF transformer (new question Output transformer) - by hotrod - 05-02-2010, 11:14 PM

Re: 38-116 IF transformer (new question Output transformer) - by hotrod - 05-03-2010, 01:38 PM

Re: 38-116 IF transformer (new question Output transformer) - by Ron Ramirez - 05-03-2010, 02:26 PM

Re: 38-116 IF transformer (new question Output transformer) - by hotrod - 05-03-2010, 05:49 PM

Re: 38-116 IF transformer (new question Output transformer) - by Ron Ramirez - 05-03-2010, 08:45 PM

Re: 38-116 IF transformer (new question Output transformer) - by hotrod - 05-04-2010, 08:58 PM

Re: 38-116 IF transformer (new question Output transformer) - by Ron Ramirez - 05-05-2010, 08:09 AM

Re: 38-116 IF transformer (new question Output transformer) - by hotrod - 05-06-2010, 01:26 AM

Re: 38-116 IF transformer (new question Output transformer) - by hotrod - 05-07-2010, 10:34 PM

Re: 38-116 IF transformer (new question Output transformer) - by hotrod - 05-25-2010, 08:28 PM

Re: 38-116 updated it works!!!! - by Ron Ramirez - 05-25-2010, 09:31 PM

Re: 38-116 updated it works!!!! - by hotrod - 05-25-2010, 10:33 PM

Re: 38-116 (It Rocks) - by hotrod - 05-31-2010, 06:36 AM

Re: 38-116 updated it works!!!! - by Ron Ramirez - 05-31-2010, 07:50 AM

Re: 38-116 updated it works!!!! - by hotrod - 05-31-2010, 05:08 PM

Re: 38-116 updated it works!!!! - by radiomikee - 06-06-2010, 09:49 PM

Re: 38-116 updated it works!!!! - by hotrod - 06-08-2010, 02:01 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5549 online users. [Complete List]
» 1 Member(s) | 5548 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me