1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Nathan's 112 Highboy
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#23

02-08-2018, 01:08 PM
+1
Also while you have it apart vacuum out the gap between the pole and frame. They tend to accumulate dust that could inhibit the cone movement.
Great job so far!!
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
Nathan's 112 Highboy - by Nathan Slingerland - 01-28-2018, 04:14 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-28-2018, 04:51 PM
RE: Nathan's 112 Highboy - by morzh - 01-28-2018, 05:11 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-28-2018, 11:08 PM
RE: Nathan's 112 Highboy - by gregb - 01-28-2018, 11:40 PM
RE: Nathan's 112 Highboy - by KCMike - 01-28-2018, 11:50 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-30-2018, 12:38 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 01:26 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 01:49 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 02:24 PM
RE: Nathan's 112 Highboy - by Kestas - 01-31-2018, 04:38 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 05:40 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 08:50 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-05-2018, 12:08 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-05-2018, 12:30 AM
RE: Nathan's 112 Highboy - by Radioroslyn - 02-05-2018, 11:45 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-05-2018, 12:01 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-08-2018, 01:02 AM
RE: Nathan's 112 Highboy - by Ron Ramirez - 02-08-2018, 06:54 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-08-2018, 07:41 AM
RE: Nathan's 112 Highboy - by Ron Ramirez - 02-08-2018, 11:02 AM
RE: Nathan's 112 Highboy - by Radioroslyn - 02-08-2018, 01:08 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-08-2018, 01:24 PM
RE: Nathan's 112 Highboy - by Steve Davis - 02-09-2018, 02:30 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-09-2018, 02:44 AM
RE: Nathan's 112 Highboy - by Radioroslyn - 02-09-2018, 11:01 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-19-2018, 09:17 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-19-2018, 09:20 PM
RE: Nathan's 112 Highboy - by morzh - 02-19-2018, 10:21 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-19-2018, 10:31 PM
RE: Nathan's 112 Highboy - by EdHolland - 02-23-2018, 07:44 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration