1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Nathan's 112 Highboy
Nathan Slingerland
Super Moderator
******
Posts: 1,874
Threads: 212
Joined: May 2015
City: Seattle State, Province, Country: WA
#24

02-08-2018, 01:24 PM
Thank you for the great advice! I will definitely do it that way next time.

For some reason I had assumed that the cone was glued to the frame not the gasket. It's great news that I was wrong. Icon_biggrin
Find
« Next Oldest | Next Newest »


Messages In This Thread
Nathan's 112 Highboy - by Nathan Slingerland - 01-28-2018, 04:14 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-28-2018, 04:51 PM
RE: Nathan's 112 Highboy - by morzh - 01-28-2018, 05:11 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-28-2018, 11:08 PM
RE: Nathan's 112 Highboy - by gregb - 01-28-2018, 11:40 PM
RE: Nathan's 112 Highboy - by KCMike - 01-28-2018, 11:50 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-30-2018, 12:38 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 01:26 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 01:49 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 02:24 PM
RE: Nathan's 112 Highboy - by Kestas - 01-31-2018, 04:38 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 05:40 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 08:50 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-05-2018, 12:08 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-05-2018, 12:30 AM
RE: Nathan's 112 Highboy - by Radioroslyn - 02-05-2018, 11:45 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-05-2018, 12:01 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-08-2018, 01:02 AM
RE: Nathan's 112 Highboy - by Ron Ramirez - 02-08-2018, 06:54 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-08-2018, 07:41 AM
RE: Nathan's 112 Highboy - by Ron Ramirez - 02-08-2018, 11:02 AM
RE: Nathan's 112 Highboy - by Radioroslyn - 02-08-2018, 01:08 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-08-2018, 01:24 PM
RE: Nathan's 112 Highboy - by Steve Davis - 02-09-2018, 02:30 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-09-2018, 02:44 AM
RE: Nathan's 112 Highboy - by Radioroslyn - 02-09-2018, 11:01 AM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-19-2018, 09:17 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-19-2018, 09:20 PM
RE: Nathan's 112 Highboy - by morzh - 02-19-2018, 10:21 PM
RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-19-2018, 10:31 PM
RE: Nathan's 112 Highboy - by EdHolland - 02-23-2018, 07:44 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 5258 online users. [Complete List]
» 1 Member(s) | 5257 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration