Nathan's 112 Highboy

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Nathan's 112 Highboy

Steve Davis
Phorum Expert

Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO

#25

02-09-2018, 02:30 AM

Nathan, I know it is too late to help on this one, but I posted a "how to" in the tech section, on how to replace speaker wires without drilling the rivets out of the plug. Look here. http://www.philcoradio.com/phorum/showth...?tid=17924

Steve

M R Radios C M Tubes

Find

« Next Oldest | Next Newest »

Messages In This Thread

Nathan's 112 Highboy - by Nathan Slingerland - 01-28-2018, 04:14 PM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-28-2018, 04:51 PM

RE: Nathan's 112 Highboy - by morzh - 01-28-2018, 05:11 PM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-28-2018, 11:08 PM

RE: Nathan's 112 Highboy - by gregb - 01-28-2018, 11:40 PM

RE: Nathan's 112 Highboy - by KCMike - 01-28-2018, 11:50 PM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-30-2018, 12:38 PM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 01:26 AM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 01:49 AM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 02:24 PM

RE: Nathan's 112 Highboy - by Kestas - 01-31-2018, 04:38 PM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 05:40 PM

RE: Nathan's 112 Highboy - by Kenneth F. Besso Jr. - 01-31-2018, 08:27 PM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 01-31-2018, 08:50 PM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-05-2018, 12:08 AM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-05-2018, 12:30 AM

RE: Nathan's 112 Highboy - by Radioroslyn - 02-05-2018, 11:45 AM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-05-2018, 12:01 PM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-08-2018, 01:02 AM

RE: Nathan's 112 Highboy - by Ron Ramirez - 02-08-2018, 06:54 AM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-08-2018, 07:41 AM

RE: Nathan's 112 Highboy - by Ron Ramirez - 02-08-2018, 11:02 AM

RE: Nathan's 112 Highboy - by Radioroslyn - 02-08-2018, 01:08 PM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-08-2018, 01:24 PM

RE: Nathan's 112 Highboy - by Steve Davis - 02-09-2018, 02:30 AM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-09-2018, 02:44 AM

RE: Nathan's 112 Highboy - by Radioroslyn - 02-09-2018, 11:01 AM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-19-2018, 09:17 PM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-19-2018, 09:20 PM

RE: Nathan's 112 Highboy - by morzh - 02-19-2018, 10:21 PM

RE: Nathan's 112 Highboy - by Nathan Slingerland - 02-19-2018, 10:31 PM

RE: Nathan's 112 Highboy - by EdHolland - 02-23-2018, 07:44 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me