1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
philco model 84
vinzer
Member
***
Posts: 214
Threads: 16
Joined: May 2010
City: Kokomo, IN
#5

05-03-2010, 09:38 PM
Most of the hum is gone when the 77 tube in sheild is pulled out of its socket I have tryed 3 77 tubes with no change I changed all off value resisters which was all but one or two. Hum is not to noticeable when tuned to a station.

The service bulitation show a humbucker but I dont see one on the speaker looks orginal speaker.
Find
« Next Oldest | Next Newest »


Messages In This Thread
philco model 84 - by vinzer - 05-02-2010, 04:37 PM
Re: philco model 84 - by 7estatdef - 05-03-2010, 08:56 AM
Re: philco model 84 - by vinzer - 05-03-2010, 06:22 PM
Re: philco model 84 - by Ron Ramirez - 05-03-2010, 08:50 PM
Re: philco model 84 - by vinzer - 05-03-2010, 09:38 PM
Re: philco model 84 - by denver - 05-03-2010, 10:56 PM
Re: philco model 84 - by vinzer - 05-08-2010, 05:14 PM
Re: philco model 84 - by rghines1 - 05-09-2010, 06:08 PM
Re: philco model 84 - by vinzer - 05-09-2010, 09:10 PM
Re: philco model 84 - by Ed Locker - 05-10-2010, 09:01 AM
Re: philco model 84 - by gary rabbitt - 05-11-2010, 11:53 PM
Re: philco model 84 - by vinzer - 05-12-2010, 11:31 AM
Re: philco model 84 - by Chuck Schwark - 05-12-2010, 01:53 PM
Re: philco model 84 - by vinzer - 05-12-2010, 02:28 PM
Re: philco model 84 - by Chuck Schwark - 05-12-2010, 03:07 PM
Re: philco model 84 - by vinzer - 05-12-2010, 04:34 PM
Re: philco model 84 - by vinzer - 05-28-2010, 05:47 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5859 online users. [Complete List]
» 2 Member(s) | 5857 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration