Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Model 20 ?
#17

At first, model 20 sets did not have a dial light. Sometime early on during production of the 20, a dial lamp was added. As was typical of Philco, it was not documented. So if yours has one and it looks as old as the rest of the chassis, be assured it is likely factory installed.

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Philco Model 20 ? - by vecher - 08-10-2017, 10:30 AM
RE: Philco Model 20 ? - by morzh - 08-10-2017, 11:02 AM
RE: Philco Model 20 ? - by OldRestorer - 08-10-2017, 11:02 AM
RE: Philco Model 20 ? - by WallaceRoger - 08-10-2017, 11:36 AM
RE: Philco Model 20 ? - by vecher - 08-10-2017, 11:57 AM
RE: Philco Model 20 ? - by Nathan Slingerland - 08-10-2017, 11:58 AM
RE: Philco Model 20 ? - by morzh - 08-10-2017, 12:06 PM
RE: Philco Model 20 ? - by vecher - 08-10-2017, 12:20 PM
RE: Philco Model 20 ? - by morzh - 08-10-2017, 01:04 PM
RE: Philco Model 20 ? - by vecher - 08-10-2017, 01:16 PM
RE: Philco Model 20 ? - by sam - 08-10-2017, 07:17 PM
RE: Philco Model 20 ? - by morzh - 08-10-2017, 07:26 PM
RE: Philco Model 20 ? - by OldRestorer - 08-10-2017, 08:02 PM
RE: Philco Model 20 ? - by Electrothaumaturgist - 10-23-2017, 12:41 PM
RE: Philco Model 20 - by vecher - 02-12-2018, 11:22 PM
RE: Philco Model 20 ? - by PhilcoPhan1936 - 02-13-2018, 12:08 AM
RE: Philco Model 20 ? - by Ron Ramirez - 02-13-2018, 05:45 AM
RE: Philco Model 20 ? - by vecher - 02-13-2018, 03:41 PM
RE: Philco Model 20 ? - by Radioroslyn - 02-13-2018, 04:29 PM
RE: Philco Model 20 ? - by vecher - 02-13-2018, 11:16 PM
RE: Philco Model 20 ? - by Radioroslyn - 02-13-2018, 11:24 PM
RE: Philco Model 20 ? - by vecher - 02-14-2018, 12:18 AM
RE: Philco Model 20 ? - by WallaceRoger - 02-14-2018, 03:24 PM
RE: Philco Model 20 ? - by vecher - 02-14-2018, 03:42 PM
RE: Philco Model 20 ? - by morzh - 02-14-2018, 03:54 PM
RE: Philco Model 20 ? - by vecher - 02-14-2018, 03:59 PM
RE: Philco Model 20 ? - by Radioroslyn - 02-14-2018, 04:16 PM
RE: Philco Model 20 ? - by vecher - 02-14-2018, 06:58 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4045 online users. [Complete List]
» 3 Member(s) | 4042 Guest(s)
AvatarAvatarAvatar

>