Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 49-901 restoration
#5

Thank you for confirming what I suspected.  A foot operated radio seemed rather silly.  

As much as I 'd like to blame shipping, it was like this when I bid on it.  Not surprising I was the only bidder.  It may have been the victim of poor packing and was returned and relisted or perhaps the damage happened a long time ago.  I'm really not sure. 

I find it very strange how chipped up the edges of the bottom piece are.  As if someone tried to open it with a crowbar Icon_confused


Messages In This Thread
Philco 49-901 restoration - by Bob Andersen - 02-27-2018, 12:01 AM
RE: Philco 49-901 restoration - by Bob Andersen - 02-27-2018, 12:53 AM
RE: Philco 49-901 restoration - by Ron Ramirez - 02-27-2018, 06:54 AM
RE: Philco 49-901 restoration - by Bob Andersen - 02-27-2018, 11:00 AM
RE: Philco 49-901 restoration - by Bob Andersen - 03-13-2018, 03:03 PM
RE: Philco 49-901 restoration - by Bob Andersen - 03-16-2018, 06:06 PM
RE: Philco 49-901 restoration - by Arran - 03-17-2018, 04:27 AM
RE: Philco 49-901 restoration - by Bob Andersen - 04-06-2018, 05:42 PM
RE: Philco 49-901 restoration - by Bob Andersen - 04-13-2018, 10:14 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

[-]
Who's Online
There are currently 1034 online users. [Complete List]
» 1 Member(s) | 1033 Guest(s)
Avatar

>