A little help Please

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

A little help Please

elfiself
Member

Posts: 58
Threads: 9
Joined: Apr 2016
City: Albany,NY

02-27-2018, 02:24 PM

Thanks again Terry.
By the way, is it common practice to use the center tap on tube sockets as a chassis grounding point? Notes I took when I disassembled the pt-7 indicate all the center taps were connected (not the rectifier), not sure why.

Find

« Next Oldest | Next Newest »

Messages In This Thread

A little help Please - by elfiself - 02-27-2018, 09:41 AM

RE: A little help Please - by Radioroslyn - 02-27-2018, 10:57 AM

RE: A little help Please - by elfiself - 02-27-2018, 02:24 PM

RE: A little help Please - by Radioroslyn - 02-27-2018, 02:58 PM

RE: A little help Please - by elfiself - 02-28-2018, 02:56 PM

RE: A little help Please - by Radioroslyn - 02-28-2018, 05:32 PM

RE: A little help Please - by elfiself - 02-28-2018, 06:01 PM

RE: A little help Please - by Kenneth F. Besso Jr. - 02-28-2018, 06:53 PM

RE: A little help Please - by elfiself - 02-28-2018, 07:18 PM

RE: A little help Please - by elfiself - 03-07-2018, 11:11 AM

RE: A little help Please - by Radioroslyn - 03-07-2018, 12:15 PM

RE: A little help Please - by elfiself - 03-07-2018, 02:21 PM

RE: A little help Please - by Radioroslyn - 03-07-2018, 03:18 PM

RE: A little help Please - by elfiself - 03-07-2018, 04:19 PM

RE: A little help Please - by Radioroslyn - 03-07-2018, 05:19 PM

RE: A little help Please - by elfiself - 03-07-2018, 08:25 PM

RE: A little help Please - by Radioroslyn - 03-07-2018, 09:09 PM

RE: A little help Please - by elfiself - 03-09-2018, 03:39 PM

RE: A little help Please - by morzh - 03-09-2018, 04:39 PM

RE: A little help Please - by elfiself - 03-09-2018, 05:13 PM

RE: A little help Please - by Radioroslyn - 03-09-2018, 05:34 PM

RE: A little help Please - by elfiself - 03-09-2018, 05:51 PM

RE: A little help Please - by elfiself - 03-10-2018, 01:04 AM

RE: A little help Please - by morzh - 03-10-2018, 10:48 AM

RE: A little help Please - by elfiself - 03-10-2018, 11:41 AM

RE: A little help Please - by morzh - 03-10-2018, 11:46 AM

RE: A little help Please - by elfiself - 03-10-2018, 11:48 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5510 online users. [Complete List]
» 1 Member(s) | 5509 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me