Westinghouse WR10A

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Westinghouse WR10A

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

02-27-2018, 09:58 PM

Unscrew.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Westinghouse WR10A - by vecher - 02-17-2018, 12:36 AM

RE: Westinghouse WR10A - by Phlogiston - 02-17-2018, 12:00 PM

RE: Westinghouse WR10A - by vecher - 02-17-2018, 11:16 PM

RE: Westinghouse WR10A - by vecher - 02-27-2018, 08:26 PM

RE: Westinghouse WR10A - by Radioroslyn - 02-27-2018, 09:58 PM

RE: Westinghouse WR10A - by vecher - 02-28-2018, 02:26 AM

RE: Westinghouse WR10A - by David - 02-28-2018, 09:18 AM

RE: Westinghouse WR10A - by Eliot Ness - 02-28-2018, 09:36 AM

RE: Westinghouse WR10A - by EdHolland - 02-28-2018, 05:42 PM

RE: Westinghouse WR10A - by vecher - 03-31-2018, 12:03 AM

RE: Westinghouse WR10A - by Arran - 03-31-2018, 12:30 AM

RE: Westinghouse WR10A - by vecher - 04-01-2018, 12:21 AM

RE: Westinghouse WR10A - by Phlogiston - 04-01-2018, 10:51 AM

RE: Westinghouse WR10A - by vecher - 04-11-2018, 11:02 PM

RE: Westinghouse WR10A - by rfeenstra - 04-11-2018, 11:54 PM

RE: Westinghouse WR10A - by Eliot Ness - 04-12-2018, 05:38 AM

RE: Westinghouse WR10A - by vecher - 04-14-2018, 06:55 PM

RE: Westinghouse WR10A - by Radioroslyn - 04-14-2018, 08:22 PM

RE: Westinghouse WR10A - by vecher - 04-14-2018, 10:45 PM

RE: Westinghouse WR10A - by vecher - 04-14-2018, 11:23 PM

RE: Westinghouse WR10A - by vecher - 04-16-2018, 12:38 AM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me