1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
A little help Please
elfiself
Member
***
Posts: 58
Threads: 9
Joined: Apr 2016
City: Albany,NY
#7

02-28-2018, 06:01 PM
Thought the used only cap said 7, tough to read. I have no sound from speaker. Field coil and OT seem to function though output is very faint. Using the AO from a EICO 324 vintage sig gen. I'm in the process of determining the correct connections of aerial and front end components. Obviously not getting a clear point to point from the schematic.
Larry
Find
« Next Oldest | Next Newest »


Messages In This Thread
A little help Please - by elfiself - 02-27-2018, 09:41 AM
RE: A little help Please - by Radioroslyn - 02-27-2018, 10:57 AM
RE: A little help Please - by elfiself - 02-27-2018, 02:24 PM
RE: A little help Please - by Radioroslyn - 02-27-2018, 02:58 PM
RE: A little help Please - by elfiself - 02-28-2018, 02:56 PM
RE: A little help Please - by Radioroslyn - 02-28-2018, 05:32 PM
RE: A little help Please - by elfiself - 02-28-2018, 06:01 PM
RE: A little help Please - by elfiself - 02-28-2018, 07:18 PM
RE: A little help Please - by elfiself - 03-07-2018, 11:11 AM
RE: A little help Please - by Radioroslyn - 03-07-2018, 12:15 PM
RE: A little help Please - by elfiself - 03-07-2018, 02:21 PM
RE: A little help Please - by Radioroslyn - 03-07-2018, 03:18 PM
RE: A little help Please - by elfiself - 03-07-2018, 04:19 PM
RE: A little help Please - by Radioroslyn - 03-07-2018, 05:19 PM
RE: A little help Please - by elfiself - 03-07-2018, 08:25 PM
RE: A little help Please - by Radioroslyn - 03-07-2018, 09:09 PM
RE: A little help Please - by elfiself - 03-09-2018, 03:39 PM
RE: A little help Please - by morzh - 03-09-2018, 04:39 PM
RE: A little help Please - by elfiself - 03-09-2018, 05:13 PM
RE: A little help Please - by Radioroslyn - 03-09-2018, 05:34 PM
RE: A little help Please - by elfiself - 03-09-2018, 05:51 PM
RE: A little help Please - by elfiself - 03-10-2018, 01:04 AM
RE: A little help Please - by morzh - 03-10-2018, 10:48 AM
RE: A little help Please - by elfiself - 03-10-2018, 11:41 AM
RE: A little help Please - by morzh - 03-10-2018, 11:46 AM
RE: A little help Please - by elfiself - 03-10-2018, 11:48 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5582 online users. [Complete List]
» 1 Member(s) | 5581 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration