1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Knobs for Philco 52-1731
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#4

03-05-2018, 11:54 PM
Philco Knobs & Pushbuttons (original)

David Frush (original and NOS knobs, including many for Philco sets)

Julie McCall - Original knobs for Philco and other radios.

Kelton Trammell - Original knobs for Philco and other radios.

Mark Oppat's Old Radio Parts

Mike Koste - Gobs of Knobs

Here at the Philco Phorum we have a Resource section has listed parts and services available for Philco sets.
Personally have had dealings w/ Julie and Mike both are top notch!

Welcome to the Phorum.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
Knobs for Philco 52-1731 - by Southpaw - 03-05-2018, 01:50 PM
RE: Knobs for Philco 52-1731 - by Southpaw - 03-05-2018, 02:19 PM
RE: Knobs for Philco 52-1731 - by Radioroslyn - 03-05-2018, 11:54 PM
RE: Knobs for Philco 52-1731 - by Southpaw - 03-06-2018, 01:13 PM
RE: Knobs for Philco 52-1731 - by Arran - 03-09-2018, 02:43 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4971 online users. [Complete List]
» 1 Member(s) | 4970 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration