1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
A little help Please
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#13

03-07-2018, 03:18 PM
>I have nothing between 26+ and the plate of the mixer !
I'm not completely sure of your answer. Do you mean you have no voltage? Or no resistance?
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
A little help Please - by elfiself - 02-27-2018, 09:41 AM
RE: A little help Please - by Radioroslyn - 02-27-2018, 10:57 AM
RE: A little help Please - by elfiself - 02-27-2018, 02:24 PM
RE: A little help Please - by Radioroslyn - 02-27-2018, 02:58 PM
RE: A little help Please - by elfiself - 02-28-2018, 02:56 PM
RE: A little help Please - by Radioroslyn - 02-28-2018, 05:32 PM
RE: A little help Please - by elfiself - 02-28-2018, 06:01 PM
RE: A little help Please - by elfiself - 02-28-2018, 07:18 PM
RE: A little help Please - by elfiself - 03-07-2018, 11:11 AM
RE: A little help Please - by Radioroslyn - 03-07-2018, 12:15 PM
RE: A little help Please - by elfiself - 03-07-2018, 02:21 PM
RE: A little help Please - by Radioroslyn - 03-07-2018, 03:18 PM
RE: A little help Please - by elfiself - 03-07-2018, 04:19 PM
RE: A little help Please - by Radioroslyn - 03-07-2018, 05:19 PM
RE: A little help Please - by elfiself - 03-07-2018, 08:25 PM
RE: A little help Please - by Radioroslyn - 03-07-2018, 09:09 PM
RE: A little help Please - by elfiself - 03-09-2018, 03:39 PM
RE: A little help Please - by morzh - 03-09-2018, 04:39 PM
RE: A little help Please - by elfiself - 03-09-2018, 05:13 PM
RE: A little help Please - by Radioroslyn - 03-09-2018, 05:34 PM
RE: A little help Please - by elfiself - 03-09-2018, 05:51 PM
RE: A little help Please - by elfiself - 03-10-2018, 01:04 AM
RE: A little help Please - by morzh - 03-10-2018, 10:48 AM
RE: A little help Please - by elfiself - 03-10-2018, 11:41 AM
RE: A little help Please - by morzh - 03-10-2018, 11:46 AM
RE: A little help Please - by elfiself - 03-10-2018, 11:48 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration