1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
1936 Philco model 84 cathedral
Guest
Unregistered
 
#5

05-14-2010, 02:05 AM
Awsome, awsome, awsome! Thank you all very much! Very good info. I was wondering if there were something inside those bakelite blocks. I just now acquired a schematic for this puppy and it shows those paper caps, but could not see them under the chassis! 8)

I was just checking the first coil which I believe (according to the schematic) is the antenna coil. It has good continuity. Which one is the oscillator coil?
« Next Oldest | Next Newest »


Messages In This Thread
1936 Philco model 84 cathedral - by Guest - 05-13-2010, 04:35 PM
Re: 1936 Philco model 84 cathedral - by vinzer - 05-13-2010, 08:11 PM
Re: 1936 Philco model 84 cathedral - by hotrod - 05-13-2010, 10:17 PM
Re: 1936 Philco model 84 cathedral - by 7estatdef - 05-13-2010, 11:53 PM
Re: 1936 Philco model 84 cathedral - by Guest - 05-14-2010, 02:05 AM
Re: 1936 Philco model 84 cathedral - by denver - 05-14-2010, 02:10 PM
Re: 1936 Philco model 84 cathedral - by vinzer - 05-14-2010, 03:58 PM
Re: 1936 Philco model 84 cathedral - by 7estatdef - 05-14-2010, 07:04 PM
Re: 1936 Philco model 84 cathedral - by 7estatdef - 05-14-2010, 07:19 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5543 online users. [Complete List]
» 1 Member(s) | 5542 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration