Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 49-901 restoration
#9

Great job as always, Bob.

I'm curious, though: why do you favor J-B Weld over fiberglass resin? Look at this example:
http://philcoradio.com/phorum/showthread.php?tid=14921

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Philco 49-901 restoration - by Bob Andersen - 03-14-2018, 04:34 PM
RE: Philco 49-901 restoration - by Bob Andersen - 03-14-2018, 05:13 PM
RE: Philco 49-901 restoration - by Bob Andersen - 03-14-2018, 05:26 PM
RE: Philco 49-901 restoration - by Bob Andersen - 03-14-2018, 05:34 PM
RE: Philco 49-901 restoration - by Arran - 03-15-2018, 12:06 AM
RE: Philco 49-901 restoration - by OldRestorer - 03-15-2018, 08:37 AM
RE: Philco 49-901 restoration - by Bob Andersen - 03-15-2018, 10:36 AM
RE: Philco 49-901 restoration - by w4rtc - 03-15-2018, 11:23 AM
RE: Philco 49-901 restoration - by Ron Ramirez - 03-15-2018, 11:37 AM
RE: Philco 49-901 restoration - by Bob Andersen - 03-15-2018, 03:08 PM
RE: Philco 49-901 restoration - by Arran - 03-16-2018, 09:16 PM
RE: Philco 49-901 restoration - by Bob Andersen - 03-25-2018, 02:51 AM
RE: Philco 49-901 restoration - by Bob Andersen - 08-14-2018, 12:19 PM
RE: Philco 49-901 restoration - by Bob Andersen - 12-10-2019, 05:46 PM
RE: Philco 49-901 restoration - by w4rtc - 12-10-2019, 07:46 PM
RE: Philco 49-901 restoration - by Bob Andersen - 12-11-2019, 01:07 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3841 online users. [Complete List]
» 1 Member(s) | 3840 Guest(s)
Avatar

>