1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
41-295 bias resistor values
mgutierres
Member
***
Posts: 51
Threads: 12
Joined: Sep 2009
City: Minneapolis, MN
#1

06-24-2010, 11:18 AM
I'm beginning chassis work on a fairly decent model 41-295, and looking through the schematic, I noticed the bias resistors are listed as: 82B=150 ohms, 82A=15 ohms, and 82=10 ohms. The parts list shows 82B as 115 ohms. Which one is correct? Also, what should the wattage of these resistors be?

Thanks in advance!
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
41-295 bias resistor values - by mgutierres - 06-24-2010, 11:18 AM
Re: 41-295 bias resistor values - by TFB - 06-24-2010, 10:17 PM
Re: 41-295 bias resistor values - by mgutierres - 06-25-2010, 01:18 AM
Re: 41-295 bias resistor values - by BDM - 06-28-2010, 01:15 AM
Re: 41-295 bias resistor values - by Raleigh - 06-28-2010, 05:44 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-480 Electronic Restoration
The sleeving for the transformer arrived early, so I went ahead and finished reassembling. The chassis looks far better ...jrblasde — 10:15 PM
Philco 610B oscillator wiring
I don't know what you are referring to when you say "tube cathode ground". Ground is a connection to the chass...RodB — 05:56 PM
Zenith H725
Good points, Arran. I haven't encountered this problem with any other radio (all earlier vintages), so am learning here....EdHolland — 05:32 PM
Zenith H725
Ed; One thing that I will say about these is that Brand Z was considerate enough to make these mica caps easily acces...Arran — 02:34 PM
Philco 610B oscillator wiring
Do you know what run # your chassis is? It took me a while to find what you were basing updates/modification on as I did...Radioroslyn — 07:34 AM
Need to purchase some accessories for restoration of my Old Philco Radio
COLLEAGUES, Thank you all for such good and important suggestions as how to find good replacement parts. I will go fo...palonso — 07:05 AM
Zenith H725
Here's what the inside of AM IFT2 looked like, and the other pic shows the discs I made to take place of the mica and ke...EdHolland — 07:40 PM
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM
My Philco 37-116 Restore
Are you measuring relative to the centertap or the GND?morzh — 11:57 PM

[-]
Who's Online
There are currently 846 online users. [Complete List]
» 4 Member(s) | 842 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration