1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Dry Sink-Philco Stereo
Guest
Unregistered
 
#1

06-18-2010, 10:06 PM
Anyone,

I just inherited from my grandmother a 1970's maple dry sink with a Philco stereo radio and turntable. It is model Q1710, SN: Q1710MA with Code 126.
It is a 50 Watt unit. It has an AFC control and a rear jack for two external speakers. It has 3 speakers on both sides of the cabinet. It has a pretty good sound and the maple finish is in really good shape. I lived with my grandparents when I went to college in 1967-1972 and played it a lot.
My question is does anyone know where I can get a manual for this unit and what ohm speakers should I get to add to the two rear external jacks? If it helps, the unit says to use Philco SS-36 or SS-45 speakers.

Sincerely,

Dbeyer
« Next Oldest | Next Newest »


Messages In This Thread
Dry Sink-Philco Stereo - by Guest - 06-18-2010, 10:06 PM
Re: Dry Sink-Philco Stereo - by Ron Ramirez - 07-04-2010, 08:13 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3440 online users. [Complete List]
» 2 Member(s) | 3438 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios