need help 45c restore

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

need help 45c restore

Danny
Member

Posts: 64
Threads: 22
Joined: Oct 2006
City: Acworth State, Province, Country: GA

#10

03-24-2018, 05:14 PM

Thanks for all the help guys....Turned out to be the tone control.
Replaced the 3 caps put it back together and it fired right up....
Again thanks for all the help. Now I'll tackle those bakelite blocks.

Danny

Find

« Next Oldest | Next Newest »

Messages In This Thread

need help 45c restore - by Danny - 03-23-2018, 01:53 PM

RE: need help 45c restore - by morzh - 03-23-2018, 03:25 PM

RE: need help 45c restore - by Danny - 03-23-2018, 03:47 PM

RE: need help 45c restore - by Radioroslyn - 03-23-2018, 06:20 PM

RE: need help 45c restore - by 45philcodon - 03-23-2018, 07:24 PM

RE: need help 45c restore - by 45philcodon - 03-23-2018, 07:45 PM

RE: need help 45c restore - by PhilcoPhan1936 - 03-23-2018, 08:27 PM

RE: need help 45c restore - by PhilcoPhan1936 - 03-23-2018, 08:30 PM

RE: need help 45c restore - by Danny - 03-24-2018, 11:23 AM

RE: need help 45c restore - by Danny - 03-24-2018, 05:14 PM

RE: need help 45c restore - by Arran - 03-24-2018, 05:36 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5464 online users. [Complete List]
» 1 Member(s) | 5463 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me