1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 14 LZX resfinish
Fred Taylor
Phorum Expert
*****
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
#5

04-09-2018, 06:57 AM
The radio chassis is sitting on its back basically I'm thinking that shouldn't make them install the dial scale numbers upside down.  If your sitting in front of radio in a chair then you would  see the numbers  correctly. I'm going to order just a regular dial scale for a model 91 with 2 bands and be done with it. Or just glue the pieces I broke off back on and clean the thing. The part number is on the little broken piece, maybe Ron can make something out of this mystery.


Attached Files Image(s)
       
(This post was last modified: 04-09-2018, 07:02 AM by Fred Taylor.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 14 LZX resfinish - by Fred Taylor - 04-08-2018, 08:09 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-08-2018, 08:13 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-08-2018, 09:11 PM
RE: Philco 14 LZX resfinish - by rfeenstra - 04-08-2018, 09:35 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-09-2018, 06:57 AM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-09-2018, 08:07 AM
RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-09-2018, 09:49 AM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-13-2018, 07:13 AM
RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-13-2018, 11:11 AM
RE: Philco 14 LZX resfinish - by gregb - 04-13-2018, 11:30 AM
RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-13-2018, 11:36 AM
RE: Philco 14 LZX resfinish - by OldRestorer - 04-14-2018, 06:45 AM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-14-2018, 08:03 AM
RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-14-2018, 08:34 AM
RE: Philco 14 LZX resfinish - by gregb - 04-14-2018, 11:00 AM
RE: Philco 14 LZX resfinish - by EdHolland - 04-14-2018, 11:47 AM
RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-14-2018, 10:38 PM
RE: Philco 14 LZX resfinish - by gregb - 04-14-2018, 10:46 PM
RE: Philco 14 LZX resfinish - by morzh - 04-15-2018, 11:43 AM
RE: Philco 14 LZX resfinish - by gregb - 04-15-2018, 12:04 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-15-2018, 10:28 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-15-2018, 10:32 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-16-2018, 07:49 AM
RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-16-2018, 10:16 AM
RE: Philco 14 LZX resfinish - by gregb - 04-16-2018, 02:25 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-21-2018, 08:36 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-21-2018, 08:40 PM
RE: Philco 14 LZX resfinish - by Phlogiston - 04-21-2018, 09:20 PM
RE: Philco 14 LZX resfinish - by Steve Davis - 04-21-2018, 10:40 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-22-2018, 02:42 PM
RE: Philco 14 LZX resfinish - by PhilcoJohn - 12-03-2018, 08:55 AM
RE: Philco 14 LZX resfinish - by Greggshere - 12-03-2018, 09:01 AM



Users browsing this thread: 12 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration