1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 14 LZX resfinish
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#7

04-09-2018, 09:49 AM
Good idea. Your dial scale is supposed to be upside down as the dial was intended to be closer to the user than the knobs were. In other words, the unit was to be placed so that the center section flips open away from the user, and the dial and controls are upside down in relation to how they are placed in a cathedral or console.
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 14 LZX resfinish - by Fred Taylor - 04-08-2018, 08:09 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-08-2018, 08:13 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-08-2018, 09:11 PM
RE: Philco 14 LZX resfinish - by rfeenstra - 04-08-2018, 09:35 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-09-2018, 06:57 AM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-09-2018, 08:07 AM
RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-09-2018, 09:49 AM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-13-2018, 07:13 AM
RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-13-2018, 11:11 AM
RE: Philco 14 LZX resfinish - by gregb - 04-13-2018, 11:30 AM
RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-13-2018, 11:36 AM
RE: Philco 14 LZX resfinish - by OldRestorer - 04-14-2018, 06:45 AM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-14-2018, 08:03 AM
RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-14-2018, 08:34 AM
RE: Philco 14 LZX resfinish - by gregb - 04-14-2018, 11:00 AM
RE: Philco 14 LZX resfinish - by EdHolland - 04-14-2018, 11:47 AM
RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-14-2018, 10:38 PM
RE: Philco 14 LZX resfinish - by gregb - 04-14-2018, 10:46 PM
RE: Philco 14 LZX resfinish - by morzh - 04-15-2018, 11:43 AM
RE: Philco 14 LZX resfinish - by gregb - 04-15-2018, 12:04 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-15-2018, 10:28 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-15-2018, 10:32 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-16-2018, 07:49 AM
RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-16-2018, 10:16 AM
RE: Philco 14 LZX resfinish - by gregb - 04-16-2018, 02:25 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-21-2018, 08:36 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-21-2018, 08:40 PM
RE: Philco 14 LZX resfinish - by Phlogiston - 04-21-2018, 09:20 PM
RE: Philco 14 LZX resfinish - by Steve Davis - 04-21-2018, 10:40 PM
RE: Philco 14 LZX resfinish - by Fred Taylor - 04-22-2018, 02:42 PM
RE: Philco 14 LZX resfinish - by PhilcoJohn - 12-03-2018, 08:55 AM
RE: Philco 14 LZX resfinish - by Greggshere - 12-03-2018, 09:01 AM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 4023 online users. [Complete List]
» 1 Member(s) | 4022 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration