Philco 14 LZX resfinish

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 14 LZX resfinish

gregb
Senior Member

Posts: 599
Threads: 24
Joined: Jan 2014
City: Edmonton AB CA

#25

04-16-2018, 02:25 PM

Hey Fred, I would just give the guys at Radio Daze a call, they will make anything you want and for the same price you would pay for the one above. I have had them done with no problems.

Gregb

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 14 LZX resfinish - by Fred Taylor - 04-08-2018, 08:09 PM

RE: Philco 14 LZX resfinish - by Fred Taylor - 04-08-2018, 08:13 PM

RE: Philco 14 LZX resfinish - by Fred Taylor - 04-08-2018, 09:11 PM

RE: Philco 14 LZX resfinish - by rfeenstra - 04-08-2018, 09:35 PM

RE: Philco 14 LZX resfinish - by Fred Taylor - 04-09-2018, 06:57 AM

RE: Philco 14 LZX resfinish - by Fred Taylor - 04-09-2018, 08:07 AM

RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-09-2018, 09:49 AM

RE: Philco 14 LZX resfinish - by Fred Taylor - 04-13-2018, 07:13 AM

RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-13-2018, 11:11 AM

RE: Philco 14 LZX resfinish - by gregb - 04-13-2018, 11:30 AM

RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-13-2018, 11:36 AM

RE: Philco 14 LZX resfinish - by OldRestorer - 04-14-2018, 06:45 AM

RE: Philco 14 LZX resfinish - by Fred Taylor - 04-14-2018, 08:03 AM

RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-14-2018, 08:34 AM

RE: Philco 14 LZX resfinish - by gregb - 04-14-2018, 11:00 AM

RE: Philco 14 LZX resfinish - by EdHolland - 04-14-2018, 11:47 AM

RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-14-2018, 10:38 PM

RE: Philco 14 LZX resfinish - by gregb - 04-14-2018, 10:46 PM

RE: Philco 14 LZX resfinish - by morzh - 04-15-2018, 11:43 AM

RE: Philco 14 LZX resfinish - by gregb - 04-15-2018, 12:04 PM

RE: Philco 14 LZX resfinish - by Fred Taylor - 04-15-2018, 10:28 PM

RE: Philco 14 LZX resfinish - by Fred Taylor - 04-15-2018, 10:32 PM

RE: Philco 14 LZX resfinish - by Fred Taylor - 04-16-2018, 07:49 AM

RE: Philco 14 LZX resfinish - by Ron Ramirez - 04-16-2018, 10:16 AM

RE: Philco 14 LZX resfinish - by gregb - 04-16-2018, 02:25 PM

RE: Philco 14 LZX resfinish - by Fred Taylor - 04-21-2018, 08:36 PM

RE: Philco 14 LZX resfinish - by Fred Taylor - 04-21-2018, 08:40 PM

RE: Philco 14 LZX resfinish - by Phlogiston - 04-21-2018, 09:20 PM

RE: Philco 14 LZX resfinish - by Kenneth F. Besso Jr. - 04-21-2018, 09:39 PM

RE: Philco 14 LZX resfinish - by Steve Davis - 04-21-2018, 10:40 PM

RE: Philco 14 LZX resfinish - by Fred Taylor - 04-22-2018, 02:42 PM

RE: Philco 14 LZX resfinish - by PhilcoJohn - 12-03-2018, 08:55 AM

RE: Philco 14 LZX resfinish - by Greggshere - 12-03-2018, 09:01 AM

View a Printable Version

Users browsing this thread: 10 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me