Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

new guy again,, 44 chassis
#1

Just wanted to bounce this off you guys before I get to deep in this unit.
I recapped and also retubed this set. Now I get no stations, I have a pretty long wirer, like 20' hooked to the antenna to the ground.
The volume can be adjusted very loud but no stations just static. I did get a small small low spanish voice at one point but thats it.

Any thoughts?
thanks all great site.
Rich


Messages In This Thread
new guy again,, 44 chassis - by safeshow - 04-27-2018, 11:41 AM
RE: new guy again,, 44 chassis - by safeshow - 04-27-2018, 12:34 PM
RE: new guy again,, 44 chassis - by morzh - 04-27-2018, 01:23 PM
RE: new guy again,, 44 chassis - by klondike98 - 04-27-2018, 02:16 PM
RE: new guy again,, 44 chassis - by safeshow - 04-27-2018, 03:19 PM
RE: new guy again,, 44 chassis - by safeshow - 04-27-2018, 03:51 PM
RE: new guy again,, 44 chassis - by klondike98 - 04-27-2018, 05:32 PM
RE: new guy again,, 44 chassis - by safeshow - 04-27-2018, 06:44 PM
RE: new guy again,, 44 chassis - by safeshow - 04-27-2018, 07:00 PM
RE: new guy again,, 44 chassis - by klondike98 - 04-27-2018, 07:04 PM
RE: new guy again,, 44 chassis - by klondike98 - 04-28-2018, 09:08 AM
RE: new guy again,, 44 chassis - by safeshow - 05-02-2018, 10:05 PM
RE: new guy again,, 44 chassis - by klondike98 - 05-02-2018, 10:53 PM
RE: new guy again,, 44 chassis - by safeshow - 05-03-2018, 08:32 AM
RE: new guy again,, 44 chassis - by safeshow - 05-04-2018, 11:29 AM
RE: new guy again,, 44 chassis - by klondike98 - 05-04-2018, 12:53 PM
RE: new guy again,, 44 chassis - by morzh - 05-04-2018, 03:20 PM
RE: new guy again,, 44 chassis - by klondike98 - 05-05-2018, 05:54 PM
New guy chassis 44 - by safeshow - 05-05-2018, 05:30 PM
RE: New guy chassis 44 - by morzh - 05-05-2018, 05:33 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently 1456 online users. [Complete List]
» 3 Member(s) | 1453 Guest(s)
AvatarAvatarAvatar

>