1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
41-608, re-installing BoL changer
Guest
Unregistered
 
#1

06-12-2010, 02:06 PM
New member here. This forum is a great resource, and I'm sure I'll be asking to pick the brains of everyone here - and for that, I thank all in advance.

The sad story: I have a 41-608 that I found while "tree-lawn shopping" (aka garbage-picking) about 30 years ago. When I rescued it, I found that someone had removed the Beam Of Light changer and mounting board, and replaced it with a wine rack, of sorts. Icon_cry There are also many other problems, but one thing at a time...

Here's the current issue. I found a BoL changer to install, but I'd like to duplicate the dimensions and cutout of the original mounting board as closely as possible. Does anyone have a 41-608 with the board easily accessible for measurement? A photo looking straight down on the board would be quite helpful too, as I could enlarge it to make a pattern for the cutout.

Thanks,

Brian
« Next Oldest | Next Newest »


Messages In This Thread
41-608, re-installing BoL changer - by Guest - 06-12-2010, 02:06 PM
Re: 41-608, re-installing BoL changer - by Guest - 06-12-2010, 07:16 PM
Re: 41-608, re-installing BoL changer - by Guest - 06-14-2010, 12:18 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A5...MrFixr55 — 06:48 AM
American Bosch Model 802 auto radio
I think it would come under either American Bosch or United American Bosch. American Bosch made sets for the American We...Arran — 05:53 AM
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM

[-]
Who's Online
There are currently 6463 online users. [Complete List]
» 2 Member(s) | 6461 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration