Difference in Schematic and chassis cap values?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Difference in Schematic and chassis cap values?

Chas
Senior Member

Posts: 693
Threads: 8
Joined: Apr 2018
City: S. Dartmouth State, Province, Country: MA

#6

05-02-2018, 06:22 PM

Quote:So I have found several cases where a cap in the chassis will have a different value than the schematic? Do you go by the schematic?

If the cap in question is original then go by the ratings. The schematic may be an update, or not, use the schematic value when the installed cap to be replaced is clearly a replacement and not OEM...

YMMV

Chas

Pliny the younger
“nihil novum nihil varium nihil quod non semel spectasse sufficiat”

Find

« Next Oldest | Next Newest »

Messages In This Thread

Difference in Schematic and chassis cap values? - by harleythatcher - 05-02-2018, 11:36 AM

RE: Difference in Schematic and chassis cap values? - by Phlogiston - 05-02-2018, 12:34 PM

RE: Difference in Schematic and chassis cap values? - by klondike98 - 05-02-2018, 01:38 PM

RE: Difference in Schematic and chassis cap values? - by harleythatcher - 05-02-2018, 01:58 PM

RE: Difference in Schematic and chassis cap values? - by klondike98 - 05-02-2018, 04:57 PM

RE: Difference in Schematic and chassis cap values? - by Chas - 05-02-2018, 06:22 PM

RE: Difference in Schematic and chassis cap values? - by Phlogiston - 05-02-2018, 07:33 PM

RE: Difference in Schematic and chassis cap values? - by Electrothaumaturgist - 05-02-2018, 09:16 PM

RE: Difference in Schematic and chassis cap values? - by Arran - 05-03-2018, 12:30 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5594 online users. [Complete List]
» 1 Member(s) | 5593 Guest(s)