Stewart Warner R-137-A

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Stewart Warner R-137-A

gregb
Senior Member

Posts: 599
Threads: 24
Joined: Jan 2014
City: Edmonton AB CA

#10

05-03-2018, 09:41 PM

One thing Murf on the candohm, measuring does not tell if it is noisy. You have to make a new resistor and disconnect the original, connect your made up one and see if there is an improvement. Many of the ones I have seen measure just fine but they are noisy when in circuit.

Gregb

Find

« Next Oldest | Next Newest »

Messages In This Thread

Stewart Warner R-137-A - by murf - 05-01-2018, 06:21 PM

RE: Stewart Warner R-137-A - by David - 05-01-2018, 07:30 PM

RE: Stewart Warner R-137-A - by murf - 05-01-2018, 09:58 PM

RE: Stewart Warner R-137-A - by Eliot Ness - 05-02-2018, 07:22 AM

RE: Stewart Warner R-137-A - by murf - 05-02-2018, 10:19 PM

RE: Stewart Warner R-137-A - by gregb - 05-02-2018, 10:46 PM

RE: Stewart Warner R-137-A - by Arran - 05-03-2018, 12:21 AM

RE: Stewart Warner R-137-A - by murf - 05-03-2018, 03:16 PM

RE: Stewart Warner R-137-A - by murf - 05-03-2018, 09:15 PM

RE: Stewart Warner R-137-A - by gregb - 05-03-2018, 09:41 PM

RE: Stewart Warner R-137-A - by murf - 05-04-2018, 06:40 PM

RE: Stewart Warner R-137-A - by gregb - 05-04-2018, 07:17 PM

RE: Stewart Warner R-137-A - by murf - 05-11-2018, 09:55 PM

RE: Stewart Warner R-137-A - by murf - 05-29-2018, 09:27 PM

RE: Stewart Warner R-137-A - by Radioroslyn - 05-29-2018, 10:16 PM

RE: Stewart Warner R-137-A - by murf - 05-30-2018, 04:46 PM

RE: Stewart Warner R-137-A - by Radioroslyn - 05-30-2018, 04:54 PM

RE: Stewart Warner R-137-A - by murf - 05-31-2018, 09:27 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me