1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
new guy again,, 44 chassis
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#24

05-04-2018, 12:53 PM
Mike, he mentioned that he meant AM instead of FM a couple posts back. He was also asking about a signal generator so I think the answer is "no" to full alignment.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
new guy again,, 44 chassis - by safeshow - 04-27-2018, 11:41 AM
RE: new guy again,, 44 chassis - by safeshow - 04-27-2018, 12:34 PM
RE: new guy again,, 44 chassis - by morzh - 04-27-2018, 01:23 PM
RE: new guy again,, 44 chassis - by klondike98 - 04-27-2018, 02:16 PM
RE: new guy again,, 44 chassis - by safeshow - 04-27-2018, 03:19 PM
RE: new guy again,, 44 chassis - by safeshow - 04-27-2018, 03:51 PM
RE: new guy again,, 44 chassis - by klondike98 - 04-27-2018, 05:32 PM
RE: new guy again,, 44 chassis - by safeshow - 04-27-2018, 06:44 PM
RE: new guy again,, 44 chassis - by safeshow - 04-27-2018, 07:00 PM
RE: new guy again,, 44 chassis - by klondike98 - 04-27-2018, 07:04 PM
RE: new guy again,, 44 chassis - by klondike98 - 04-28-2018, 09:08 AM
RE: new guy again,, 44 chassis - by safeshow - 05-02-2018, 10:05 PM
RE: new guy again,, 44 chassis - by klondike98 - 05-02-2018, 10:53 PM
RE: new guy again,, 44 chassis - by safeshow - 05-03-2018, 08:32 AM
RE: new guy again,, 44 chassis - by safeshow - 05-04-2018, 11:29 AM
RE: new guy again,, 44 chassis - by klondike98 - 05-04-2018, 12:53 PM
RE: new guy again,, 44 chassis - by morzh - 05-04-2018, 03:20 PM
RE: new guy again,, 44 chassis - by klondike98 - 05-05-2018, 05:54 PM
New guy chassis 44 - by safeshow - 05-05-2018, 05:30 PM
RE: New guy chassis 44 - by morzh - 05-05-2018, 05:33 PM



Users browsing this thread: 14 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

[-]
Who's Online
There are currently 7374 online users. [Complete List]
» 1 Member(s) | 7373 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration