1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
philco 16B
Steve Davis
Phorum Expert
*****
Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
#8

06-15-2010, 11:17 PM
Ron, I used a Fram 3980 that I removed from my truck. Just dig the gasket out of the base of the filter with a screwdriver. The OD turned out to be a little small,it had a tendency to slip a little, so I installed one layer denim material on the drum with contact cement and reinstalled the gasket. It then worked perfect. It could be that other brands of filters or other part numbers may fit better.
Steve

[Edited correct filter number in orig post here. CS]
M R Radios   C M Tubes
Find
« Next Oldest | Next Newest »


Messages In This Thread
philco 16B - by theboyzz - 06-15-2010, 08:57 PM
RE: philco 16B - by Steve Davis - 04-08-2015, 10:59 PM
RE: philco 16B - by Stall-U-Rated - 02-02-2019, 06:53 PM
RE: philco 16B - by morzh - 02-02-2019, 07:56 PM
RE: philco 16B - by Ron Ramirez - 02-02-2019, 08:27 PM
RE: philco 16B - by morzh - 02-02-2019, 08:51 PM
RE: philco 16B - by Ron Ramirez - 02-03-2019, 09:07 AM
RE: philco 16B - by Kenneth F. Besso Jr. - 02-03-2019, 07:07 PM
RE: philco 16B - by radiohenry - 02-04-2019, 06:46 PM
Re: philco 16B - by Ron Ramirez - 06-15-2010, 09:58 PM
Re: philco 16B - by Ron Ramirez - 06-15-2010, 10:01 PM
Re: philco 16B - by Steve Davis - 06-15-2010, 10:04 PM
Re: philco 16B - by Steve Davis - 06-15-2010, 10:06 PM
Re: philco 16B - by theboyzz - 06-15-2010, 10:09 PM
Re: philco 16B - by Ron Ramirez - 06-15-2010, 10:48 PM
Re: philco 16B - by Steve Davis - 06-15-2010, 11:17 PM
Re: philco 16B - by Ron Ramirez - 06-17-2010, 07:39 AM
Re: philco 16B - by Steve Davis - 06-17-2010, 07:05 PM
Re: philco 16B - by Ron Ramirez - 06-17-2010, 07:13 PM
Re: philco 16B - by Steve Davis - 06-17-2010, 07:20 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5546 online users. [Complete List]
» 1 Member(s) | 5545 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios