Zenith 6S527 E-cap ?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Zenith 6S527 E-cap ?

Eric
Senior Member

Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA

#9

05-07-2018, 05:41 PM

Thing is under the chassis are 4 trimmers besides the tuner trimmers (also under the chassis ) and the IF's are on top A,B,C&D
So there is
E wavetrap padder found
F broadcast padder osc
G " ant padder on tuner found.
J broadcast padder
K sw osc on tuner found
M sw padder antenna
Got a print from Radiomuseum and it shows the location of some but not all and no alignment procedure. So this is where I'm at hope to ID the rest and locate then go from there.

Eric

Find

« Next Oldest | Next Newest »

Messages In This Thread

Zenith 6S527 E-cap ? - by Eric - 04-17-2018, 03:41 PM

RE: Zenith 6S527 E-cap ? - by morzh - 04-17-2018, 04:26 PM

RE: Zenith 6S527 E-cap ? - by Eric - 04-18-2018, 10:26 AM

RE: Zenith 6S527 E-cap ? - by morzh - 04-18-2018, 12:02 PM

RE: Zenith 6S527 E-cap ? - by Arran - 04-20-2018, 12:01 AM

RE: Zenith 6S527 E-cap ? - by morzh - 04-20-2018, 08:39 AM

RE: Zenith 6S527 E-cap ? - by Eric - 05-05-2018, 10:09 AM

RE: Zenith 6S527 E-cap ? - by morzh - 05-05-2018, 12:42 PM

RE: Zenith 6S527 E-cap ? - by Eric - 05-07-2018, 05:41 PM

RE: Zenith 6S527 E-cap ? - by tbone - 05-07-2018, 07:28 PM

RE: Zenith 6S527 E-cap ? - by Eric - 05-08-2018, 02:04 PM

RE: Zenith 6S527 E-cap ? - by tbone - 05-19-2018, 09:17 AM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online
There are currently no members online.