Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 37-690 Restoration
#9

They probably could have gotten away with just the RF and IF tubes in shields. Or with no tubes in shields if they were willing to put up with RF interference and or images and noise. These issues are usually not severe enough to limit broadcast band listening (but can be). But, if they wanted to pull SW out of the weeds, it was a good idea.

If you really want to prove this, try to do an alignment without the shields or just run the radio without the shields.

OH, the osc. tube really needs the shield too.

Better radios usually have better shielding.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/


Messages In This Thread
Philco 37-690 Restoration - by Kenradio - 05-11-2018, 05:33 AM
RE: Philco 37-690 Restoration - by Ron Ramirez - 05-11-2018, 07:47 PM
RE: Philco 37-690 Restoration - by Kenradio - 05-12-2018, 05:48 AM
RE: Philco 37-690 Restoration - by morzh - 05-12-2018, 10:10 PM
RE: Philco 37-690 Restoration - by Kenradio - 05-13-2018, 04:51 AM
RE: Philco 37-690 Restoration - by Ron Ramirez - 05-13-2018, 07:38 AM
RE: Philco 37-690 Restoration - by Kenradio - 05-13-2018, 09:03 AM
RE: Philco 37-690 Restoration - by GarySP - 05-13-2018, 09:44 AM
RE: Philco 37-690 Restoration - by Phlogiston - 05-13-2018, 10:21 AM
RE: Philco 37-690 Restoration - by Kenradio - 05-13-2018, 04:30 PM
RE: Philco 37-690 Restoration - by Ron Ramirez - 05-13-2018, 07:42 PM
RE: Philco 37-690 Restoration - by Ron Ramirez - 05-13-2018, 07:44 PM
RE: Philco 37-690 Restoration - by Kenradio - 05-15-2018, 06:26 AM
RE: Philco 37-690 Restoration - by Kenradio - 05-15-2018, 06:36 AM
RE: Philco 37-690 Restoration - by morzh - 05-15-2018, 08:14 AM
RE: Philco 37-690 Restoration - by Ron Ramirez - 05-15-2018, 09:05 AM
RE: Philco 37-690 Restoration - by Kenradio - 05-15-2018, 11:22 AM
RE: Philco 37-690 Restoration - by tbone - 05-19-2018, 08:19 AM
RE: Philco 37-690 Restoration - by Phlogiston - 05-19-2018, 09:39 AM
RE: Philco 37-690 Restoration - by Ron Ramirez - 05-19-2018, 02:54 PM
RE: Philco 37-690 Restoration - by Kenradio - 05-19-2018, 06:02 PM
RE: Philco 37-690 Restoration - by tbone - 05-20-2018, 08:15 PM
RE: Philco 37-690 Restoration - by Kenradio - 05-21-2018, 04:37 AM
RE: Philco 37-690 Restoration - by Kenradio - 05-26-2018, 06:19 AM
RE: Philco 37-690 Restoration - by WyTex - 05-26-2018, 08:01 AM
RE: Philco 37-690 Restoration - by morzh - 05-26-2018, 10:40 AM
RE: Philco 37-690 Restoration - by Kenradio - 05-26-2018, 12:29 PM
RE: Philco 37-690 Restoration - by KCMike - 05-26-2018, 12:32 PM
RE: Philco 37-690 Restoration - by morzh - 05-26-2018, 01:44 PM
RE: Philco 37-690 Restoration - by Kenradio - 05-26-2018, 02:40 PM
RE: Philco 37-690 Restoration - by morzh - 05-26-2018, 02:58 PM
RE: Philco 37-690 Restoration - by Kenradio - 05-26-2018, 03:16 PM
RE: Philco 37-690 Restoration - by tbone - 06-09-2018, 06:38 AM
RE: Philco 37-690 Restoration - by Kenradio - 06-09-2018, 06:50 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>