Philco 37-690 Restoration

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 37-690 Restoration

Kenradio
Member

Posts: 98
Threads: 20
Joined: Nov 2011
City: Tiffin, Ohio

#11

05-13-2018, 04:30 PM

I had to replace 3 metal tubes that were in my 37-690 when I got it--luckily I had some spare Philco tube shields to use. My Philco 38-1 has all of its tube shields also. Ken

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 37-690 Restoration - by Kenradio - 05-11-2018, 05:33 AM

RE: Philco 37-690 Restoration - by Ron Ramirez - 05-11-2018, 07:47 PM

RE: Philco 37-690 Restoration - by Kenradio - 05-12-2018, 05:48 AM

RE: Philco 37-690 Restoration - by morzh - 05-12-2018, 10:10 PM

RE: Philco 37-690 Restoration - by Kenradio - 05-13-2018, 04:51 AM

RE: Philco 37-690 Restoration - by Ron Ramirez - 05-13-2018, 07:38 AM

RE: Philco 37-690 Restoration - by Kenradio - 05-13-2018, 09:03 AM

RE: Philco 37-690 Restoration - by GarySP - 05-13-2018, 09:44 AM

RE: Philco 37-690 Restoration - by Phlogiston - 05-13-2018, 10:21 AM

RE: Philco 37-690 Restoration - by Electrothaumaturgist - 05-13-2018, 04:07 PM

RE: Philco 37-690 Restoration - by Kenradio - 05-13-2018, 04:30 PM

RE: Philco 37-690 Restoration - by Ron Ramirez - 05-13-2018, 07:42 PM

RE: Philco 37-690 Restoration - by Ron Ramirez - 05-13-2018, 07:44 PM

RE: Philco 37-690 Restoration - by Kenradio - 05-15-2018, 06:26 AM

RE: Philco 37-690 Restoration - by Kenradio - 05-15-2018, 06:36 AM

RE: Philco 37-690 Restoration - by morzh - 05-15-2018, 08:14 AM

RE: Philco 37-690 Restoration - by Ron Ramirez - 05-15-2018, 09:05 AM

RE: Philco 37-690 Restoration - by Kenradio - 05-15-2018, 11:22 AM

RE: Philco 37-690 Restoration - by tbone - 05-19-2018, 08:19 AM

RE: Philco 37-690 Restoration - by Phlogiston - 05-19-2018, 09:39 AM

RE: Philco 37-690 Restoration - by Ron Ramirez - 05-19-2018, 02:54 PM

RE: Philco 37-690 Restoration - by Kenradio - 05-19-2018, 06:02 PM

RE: Philco 37-690 Restoration - by tbone - 05-20-2018, 08:15 PM

RE: Philco 37-690 Restoration - by Kenradio - 05-21-2018, 04:37 AM

RE: Philco 37-690 Restoration - by Kenradio - 05-26-2018, 06:19 AM

RE: Philco 37-690 Restoration - by WyTex - 05-26-2018, 08:01 AM

RE: Philco 37-690 Restoration - by morzh - 05-26-2018, 10:40 AM

RE: Philco 37-690 Restoration - by Kenradio - 05-26-2018, 12:29 PM

RE: Philco 37-690 Restoration - by KCMike - 05-26-2018, 12:32 PM

RE: Philco 37-690 Restoration - by morzh - 05-26-2018, 01:44 PM

RE: Philco 37-690 Restoration - by Kenradio - 05-26-2018, 02:40 PM

RE: Philco 37-690 Restoration - by morzh - 05-26-2018, 02:58 PM

RE: Philco 37-690 Restoration - by Kenradio - 05-26-2018, 03:16 PM

RE: Philco 37-690 Restoration - by tbone - 06-09-2018, 06:38 AM

RE: Philco 37-690 Restoration - by Kenradio - 06-09-2018, 06:50 PM

View a Printable Version

Users browsing this thread: 10 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me