1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Started my 41-295x restore.
Arran
Phorum Expert
*****
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#5

05-14-2018, 12:06 AM
Use acetone or paint and varnish remover on the bars, preferably on the whole cabinet, it's only lacquer, with sandpaper you are taking material off that you don't need to and may damage some moldings in the process.
Regards
Arran
Find
« Next Oldest | Next Newest »


Messages In This Thread
Started my 41-295x restore. - by nortonz - 05-11-2018, 01:19 AM
RE: Started my 41-295x restore. - by nortonz - 05-11-2018, 01:25 AM
RE: Started my 41-295x restore. - by nortonz - 05-11-2018, 05:11 PM
RE: Started my 41-295x restore. - by nortonz - 05-13-2018, 07:45 PM
RE: Started my 41-295x restore. - by Arran - 05-14-2018, 12:06 AM
RE: Started my 41-295x restore. - by nortonz - 05-14-2018, 01:22 PM
RE: Started my 41-295x restore. - by Arran - 05-14-2018, 09:15 PM
RE: Started my 41-295x restore. - by nortonz - 05-15-2018, 02:01 AM
RE: Started my 41-295x restore. - by nortonz - 05-15-2018, 03:37 PM
RE: Started my 41-295x restore. - by Ron Ramirez - 05-15-2018, 06:02 PM
RE: Started my 41-295x restore. - by rfeenstra - 05-16-2018, 12:57 AM
RE: Started my 41-295x restore. - by nortonz - 05-18-2018, 01:42 AM
RE: Started my 41-295x restore. - by nortonz - 06-20-2018, 11:45 PM
RE: Started my 41-295x restore. - by nortonz - 06-30-2018, 12:33 AM
RE: Started my 41-295x restore. - by 1MohrRadio - 12-29-2018, 07:28 AM
RE: Started my 41-295x restore. - by nortonz - 02-10-2019, 01:59 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM

[-]
Who's Online
There are currently 5252 online users. [Complete List]
» 1 Member(s) | 5251 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration