Started my 41-295x restore.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Started my 41-295x restore.

nortonz
Member

Posts: 88
Threads: 17
Joined: May 2018
City: Hayden, ID

#12

05-18-2018, 01:42 AM

I have the grain filler on order, have the nicks all fielded in. Will start the next step when the Mohawk grain filler gets here next week. The radio is all but done. Looking forward to seeing how it comes out.
Michael

Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Started my 41-295x restore. - by nortonz - 05-11-2018, 01:19 AM

RE: Started my 41-295x restore. - by nortonz - 05-11-2018, 01:25 AM

RE: Started my 41-295x restore. - by nortonz - 05-11-2018, 05:11 PM

RE: Started my 41-295x restore. - by nortonz - 05-13-2018, 07:45 PM

RE: Started my 41-295x restore. - by Arran - 05-14-2018, 12:06 AM

RE: Started my 41-295x restore. - by nortonz - 05-14-2018, 01:22 PM

RE: Started my 41-295x restore. - by Arran - 05-14-2018, 09:15 PM

RE: Started my 41-295x restore. - by nortonz - 05-15-2018, 02:01 AM

RE: Started my 41-295x restore. - by nortonz - 05-15-2018, 03:37 PM

RE: Started my 41-295x restore. - by Ron Ramirez - 05-15-2018, 06:02 PM

RE: Started my 41-295x restore. - by rfeenstra - 05-16-2018, 12:57 AM

RE: Started my 41-295x restore. - by nortonz - 05-18-2018, 01:42 AM

RE: Started my 41-295x restore. - by nortonz - 06-20-2018, 11:45 PM

RE: Started my 41-295x restore. - by nortonz - 06-30-2018, 12:33 AM

RE: Started my 41-295x restore. - by 1MohrRadio - 12-29-2018, 07:28 AM

RE: Started my 41-295x restore. - by nortonz - 02-10-2019, 01:59 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM

Who's Online

There are currently 4898 online users. [Complete List]
» 1 Member(s) | 4897 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me