model id?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

model id?

Arran
Phorum Expert

Posts: 4,639
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA

#4

05-19-2018, 01:37 AM

In my opinion $75 is too much for just a cabinet, in that condition. For $75 it should be more or less complete with the chassis and speaker in it, 40-180s are a very common model that turn up on fleabay with great regularity, and not for very much either. I wouldn't give the guy more then about $20 for that cabinet, if I already had the rest of the parts and even wanted it, by the time you add up the cost of getting the chassis, speaker, knobs, pushbuttons, and antenna you would be into it for $200 or more before you even get around to the restoration part.
Regards
Arran

Find

« Next Oldest | Next Newest »

Messages In This Thread

model id? - by nortonz - 05-18-2018, 07:21 PM

RE: model id? - by Ron Ramirez - 05-18-2018, 08:07 PM

RE: model id? - by nortonz - 05-18-2018, 09:45 PM

RE: model id? - by Arran - 05-19-2018, 01:37 AM

RE: model id? - by Ron Ramirez - 05-19-2018, 01:49 PM

RE: model id? - by GarySP - 05-20-2018, 07:17 PM

RE: model id? - by Kestas - 05-23-2018, 11:28 AM

RE: model id? - by nortonz - 05-23-2018, 12:18 PM

RE: model id? - by Arran - 05-25-2018, 02:11 AM

RE: model id? - by nortonz - 05-25-2018, 11:24 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

Who's Online
There are currently no members online.