Paint stripper

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Paint stripper

tbone
Senior Member

Posts: 274
Threads: 18
Joined: Nov 2016
City: Cromwell State, Province, Country: CT

#13

05-19-2018, 07:04 AM

I see mention about fish-eyes and worry of contamination because of residue left behind. I agree that this can happen as it’s sometimes hard to get every bit clean.

I use a product called “Seal Coat” by Zinnser, after I strip, sand, and stain with golden oak dye stain. This is shellac made for this purpose and it saves you from having to mix it. Wash coats of shellac have been recommended for years.

I’ve grain filled over the Seal Coat and used pigment stains with no issues at all.

https://www.rustoleum.com/product-catalo...ing-sealer

Tony

“People may not remember how fast you did a job, but they will remember how well you did it”

Find

« Next Oldest | Next Newest »

Messages In This Thread

Paint stripper - by 45philcodon - 01-05-2018, 03:03 PM

RE: Paint stripper - by rfeenstra - 01-05-2018, 04:36 PM

RE: Paint stripper - by 45philcodon - 01-05-2018, 05:47 PM

RE: Paint stripper - by Arran - 01-06-2018, 01:06 AM

RE: Paint stripper - by tbone - 02-14-2018, 06:36 PM

RE: Paint stripper - by Phlogiston - 02-15-2018, 10:38 AM

RE: Paint stripper - by Paul Philco322 - 02-15-2018, 08:09 PM

RE: Paint stripper - by tbone - 02-16-2018, 08:26 PM

RE: Paint stripper - by doug-5er - 02-26-2018, 08:21 PM

RE: Paint stripper - by oscartg - 05-18-2018, 11:24 AM

RE: Paint stripper - by Phlogiston - 05-18-2018, 11:45 AM

RE: Paint stripper - by John Bartley - 05-18-2018, 02:11 PM

RE: Paint stripper - by tbone - 05-19-2018, 07:04 AM

RE: Paint stripper - by 45philcodon - 05-20-2018, 04:23 PM

RE: Paint stripper - by Greggshere - 09-01-2018, 08:37 PM

RE: Paint stripper - by tbone - 09-02-2018, 05:06 PM

RE: Paint stripper - by Phlogiston - 09-02-2018, 07:02 PM

RE: Paint stripper - by Ron Ramirez - 09-02-2018, 08:57 PM

RE: Paint stripper - by Arran - 09-03-2018, 03:45 AM

RE: Paint stripper - by Greggshere - 09-10-2018, 10:15 AM

RE: Paint stripper - by Phlogiston - 09-10-2018, 02:59 PM

RE: Paint stripper - by Greggshere - 09-10-2018, 03:31 PM

RE: Paint stripper - by Phlogiston - 09-10-2018, 06:29 PM

RE: Paint stripper - by Arran - 09-11-2018, 02:46 AM

RE: Paint stripper - by Greggshere - 09-11-2018, 10:01 AM

RE: Paint stripper - by Phlogiston - 09-11-2018, 11:29 AM

RE: Paint stripper - by Greggshere - 09-11-2018, 03:52 PM

RE: Paint stripper - by Radioroslyn - 09-11-2018, 05:51 PM

RE: Paint stripper - by Phlogiston - 09-11-2018, 06:39 PM

RE: Paint stripper - by Ron Ramirez - 09-11-2018, 06:58 PM

RE: Paint stripper - by Radioroslyn - 09-11-2018, 07:14 PM

RE: Paint stripper - by Greggshere - 09-11-2018, 11:33 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me