Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Stewart Warner R-137-A
#14

Ok guy's,
Got it to load the pics of the questionable caps tonight.
You can see the extra long 15 volt cap in one picture and the other picture shows the cap with the flexible resistor attached.
Wondering what the purpose of the flexible resistor is that is mounted to the cap?
I have replaced those caps before by just reattaching the resistor to the new cap.
But always wondered why it was done this way.
The other pic that shows the extra long cap with the weird values.
What would be a suitable replacement. Don't have anything even close to those values.
Thanks, murf

[Image: http://i1161.photobucket.com/albums/q509...C_0363.jpg][Image: http://i1161.photobucket.com/albums/q509...C_0362.jpg]


Messages In This Thread
Stewart Warner R-137-A - by murf - 05-01-2018, 06:21 PM
RE: Stewart Warner R-137-A - by David - 05-01-2018, 07:30 PM
RE: Stewart Warner R-137-A - by murf - 05-01-2018, 09:58 PM
RE: Stewart Warner R-137-A - by Eliot Ness - 05-02-2018, 07:22 AM
RE: Stewart Warner R-137-A - by murf - 05-02-2018, 10:19 PM
RE: Stewart Warner R-137-A - by gregb - 05-02-2018, 10:46 PM
RE: Stewart Warner R-137-A - by Arran - 05-03-2018, 12:21 AM
RE: Stewart Warner R-137-A - by murf - 05-03-2018, 03:16 PM
RE: Stewart Warner R-137-A - by murf - 05-03-2018, 09:15 PM
RE: Stewart Warner R-137-A - by gregb - 05-03-2018, 09:41 PM
RE: Stewart Warner R-137-A - by murf - 05-04-2018, 06:40 PM
RE: Stewart Warner R-137-A - by gregb - 05-04-2018, 07:17 PM
RE: Stewart Warner R-137-A - by murf - 05-11-2018, 09:55 PM
RE: Stewart Warner R-137-A - by murf - 05-29-2018, 09:27 PM
RE: Stewart Warner R-137-A - by Radioroslyn - 05-29-2018, 10:16 PM
RE: Stewart Warner R-137-A - by murf - 05-30-2018, 04:46 PM
RE: Stewart Warner R-137-A - by Radioroslyn - 05-30-2018, 04:54 PM
RE: Stewart Warner R-137-A - by murf - 05-31-2018, 09:27 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5507 online users. [Complete List]
» 1 Member(s) | 5506 Guest(s)
Avatar

>