1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Line cord 42-1008
mikethedruid
Banned
Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN
#13

06-10-2018, 03:49 PM
A possible solution for those who want to replace a power cord through one of these fanged holes is to buy a roll of the uncured rubber electrical tape from any good hardware store. Wrap some around the cord where it will pass through the hole. make it thick enough in diameter so that it needs to be squashed a bit to fit through. It will cure into solid rubber after a while, it will protect the cord, and act just like a "molded on" strain relief.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Line cord 42-1008 - by soldersucker - 05-29-2018, 04:10 PM
RE: Line cord 42-1008 - by NostalgiaRadioTime - 05-29-2018, 06:30 PM
RE: Line cord 42-1008 - by Ron Ramirez - 05-29-2018, 07:08 PM
RE: Line cord 42-1008 - by Patrick - 05-29-2018, 09:05 PM
RE: Line cord 42-1008 - by NostalgiaRadioTime - 05-29-2018, 10:47 PM
RE: Line cord 42-1008 - by Arran - 05-30-2018, 03:19 AM
RE: Line cord 42-1008 - by Ron Ramirez - 05-30-2018, 06:06 AM
RE: Line cord 42-1008 - by Ed Locker - 05-30-2018, 09:14 AM
RE: Line cord 42-1008 - by soldersucker - 06-09-2018, 09:20 PM
RE: Line cord 42-1008 - by Arran - 06-09-2018, 10:07 PM
RE: Line cord 42-1008 - by soldersucker - 06-10-2018, 07:55 AM
RE: Line cord 42-1008 - by soldersucker - 06-10-2018, 08:50 AM
RE: Line cord 42-1008 - by mikethedruid - 06-10-2018, 03:49 PM
RE: Line cord 42-1008 - by soldersucker - 06-10-2018, 08:09 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration