Need help ID'ing console ('29 Model 65?)

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Need help ID'ing console ('29 Model 65?)

Chuck Schwark
Phorum Expert

Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL

02-01-2006, 11:52 PM

Great! The underside is very clean and appears untouched. You're in luck! Icon_smile

The four brown phenolic tubes with solder lugs on them are resistor/cap combo's: parts 5, 6, 10 and 27. They can be re-stuffed and remain original looking.

The big wire-wound ceramic power resistor is the "BC" resistor, part 24. It is shown in two sections on the schematic; one part is the filament winding center-tap for the 45 tubes and the other is in the power supply output resistor network.

Chuck Schwark,
The Philco Repair Bench
[Image: http://www.philcorepairbench.com/images/philog3tiny.gif]
http://www.philcorepairbench.com

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Need help ID'ing console ('29 Model 65?) - by noiseguy - 01-30-2006, 11:51 PM

[No subject] - by Chuck Schwark - 01-31-2006, 12:21 AM

[No subject] - by noiseguy - 01-31-2006, 09:55 AM

[No subject] - by Ron Ramirez - 01-31-2006, 09:59 AM

[No subject] - by Chuck Schwark - 01-31-2006, 10:03 AM

[No subject] - by Ron Ramirez - 01-31-2006, 01:06 PM

[No subject] - by rjm - 01-31-2006, 03:33 PM

[No subject] - by noiseguy - 02-01-2006, 11:40 PM

[No subject] - by Chuck Schwark - 02-01-2006, 11:52 PM

[No subject] - by noiseguy - 02-02-2006, 05:09 PM

[No subject] - by Chuck Schwark - 02-02-2006, 05:44 PM

[No subject] - by noiseguy - 02-17-2006, 01:09 PM

[No subject] - by rjm - 02-17-2006, 02:15 PM

[No subject] - by noiseguy - 03-27-2006, 12:45 AM

[No subject] - by rjm - 03-27-2006, 02:01 AM

[No subject] - by noiseguy - 03-27-2006, 09:12 AM

[No subject] - by noiseguy - 03-27-2006, 09:34 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me