Stromberg Carlson model 60

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Stromberg Carlson model 60

Eric
Senior Member

Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA

#13

06-14-2018, 04:12 PM

Mike,
Finale got the radio I'm doing it for an older (70) gentleman and it is more of a basket case than I thought but I'm going to give it a shot. Your pictures are going to be a big help I can see that already. My first question concerns the speaker, Did you make a diagram of the hook up? (I see six pins but I figure 2 for the FC and 2 for the output transformer)

I see you used a tube socket for a plug good idea.
Any help will be greatly appreciated.
Eric

Find

« Next Oldest | Next Newest »

Messages In This Thread

Stromberg Carlson model 60 - by KCMike - 04-02-2017, 07:05 PM

RE: Stromberg Carlson model 60 - by Arran - 04-03-2017, 04:05 AM

RE: Stromberg Carlson model 60 - by KCMike - 04-03-2017, 01:40 PM

RE: Stromberg Carlson model 60 - by Radioroslyn - 04-04-2017, 06:03 AM

RE: Stromberg Carlson model 60 - by Arran - 04-04-2017, 10:47 PM

RE: Stromberg Carlson model 60 - by KCMike - 04-05-2017, 05:11 PM

RE: Stromberg Carlson model 60 - by KCMike - 04-08-2017, 01:15 PM

RE: Stromberg Carlson model 60 - by Joe Rossi - 04-09-2017, 08:46 PM

RE: Stromberg Carlson model 60 - by KCMike - 04-10-2017, 09:58 AM

RE: Stromberg Carlson model 60 - by Eric - 06-06-2018, 09:20 AM

RE: Stromberg Carlson model 60 - by KCMike - 06-06-2018, 12:18 PM

RE: Stromberg Carlson model 60 - by Eric - 06-06-2018, 07:25 PM

RE: Stromberg Carlson model 60 - by Eric - 06-14-2018, 04:12 PM

RE: Stromberg Carlson model 60 - by KCMike - 06-14-2018, 04:37 PM

RE: Stromberg Carlson model 60 - by Eric - 06-14-2018, 05:53 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5494 online users. [Complete List]
» 1 Member(s) | 5493 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me