Replacing a missing speaker

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Replacing a missing speaker

Eric
Senior Member

Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA

#12

06-17-2018, 05:50 PM

Replaced the all the electrolytic's and the safety caps and most of the other caps except those in the potted can. tested the tubes, the power transformer test good (worried about that one)!
Found a speaker to use as a test but am unsure of the hook up.
The output Xformer would go across # 1&6 large pins ?
and the FC would go across # 3 & 5?
Looking from the connection side of the socket going cw with the first large pin being # 1.
Do I have it right?

Find

« Next Oldest | Next Newest »

Messages In This Thread

Replacing a missing speaker - by Eric - 06-08-2018, 08:56 AM

RE: Replacing a missing speaker - by KCMike - 06-08-2018, 10:02 AM

RE: Replacing a missing speaker - by Eric - 06-08-2018, 02:00 PM

RE: Replacing a missing speaker - by Radioroslyn - 06-08-2018, 02:56 PM

RE: Replacing a missing speaker - by KCMike - 06-08-2018, 03:03 PM

RE: Replacing a missing speaker - by Radioroslyn - 06-08-2018, 03:21 PM

RE: Replacing a missing speaker - by Arran - 06-09-2018, 02:41 AM

RE: Replacing a missing speaker - by Chas - 06-09-2018, 10:03 AM

RE: Replacing a missing speaker - by Eric - 06-10-2018, 02:40 PM

RE: Replacing a missing speaker - by Eric - 06-10-2018, 03:10 PM

RE: Replacing a missing speaker - by Arran - 06-11-2018, 02:24 AM

RE: Replacing a missing speaker - by Eric - 06-17-2018, 05:50 PM

RE: Replacing a missing speaker - by KCMike - 06-17-2018, 06:20 PM

RE: Replacing a missing speaker - by Eric - 06-17-2018, 07:45 PM

RE: Replacing a missing speaker - by KCMike - 06-17-2018, 07:58 PM

RE: Replacing a missing speaker - by Eric - 06-18-2018, 11:52 AM

RE: Replacing a missing speaker - by KCMike - 06-18-2018, 01:23 PM

RE: Replacing a missing speaker - by Radioroslyn - 06-18-2018, 01:34 PM

RE: Replacing a missing speaker - by Eric - 06-18-2018, 03:34 PM

RE: Replacing a missing speaker - by Eric - 06-18-2018, 04:00 PM

RE: Replacing a missing speaker - by KCMike - 06-18-2018, 05:34 PM

RE: Replacing a missing speaker - by Eric - 06-19-2018, 07:58 AM

RE: Replacing a missing speaker - by KCMike - 06-19-2018, 08:47 AM

RE: Replacing a missing speaker - by Eric - 06-19-2018, 09:50 AM

RE: Replacing a missing speaker - by Eric - 06-28-2018, 01:02 PM

RE: Replacing a missing speaker - by Radioroslyn - 06-28-2018, 04:44 PM

RE: Replacing a missing speaker - by Eric - 06-28-2018, 10:07 PM

RE: Replacing a missing speaker - by Radioroslyn - 06-29-2018, 03:12 PM

RE: Replacing a missing speaker - by Eric - 06-30-2018, 10:14 AM

RE: Replacing a missing speaker - by Radioroslyn - 06-30-2018, 11:47 AM

RE: Replacing a missing speaker - by Eric - 07-02-2018, 03:44 PM

RE: Replacing a missing speaker - by Eric - 07-10-2018, 02:56 PM

RE: Replacing a missing speaker - by Radioroslyn - 07-10-2018, 03:19 PM

RE: Replacing a missing speaker - by Eric - 07-10-2018, 05:06 PM

RE: Replacing a missing speaker - by Eric - 07-12-2018, 09:54 AM

RE: Replacing a missing speaker - by KCMike - 07-12-2018, 10:11 AM

RE: Replacing a missing speaker - by Eric - 07-12-2018, 04:18 PM

RE: Replacing a missing speaker - by Eric - 07-14-2018, 09:35 AM

RE: Replacing a missing speaker - by KCMike - 07-14-2018, 10:51 AM

RE: Replacing a missing speaker - by Eric - 07-14-2018, 05:01 PM

RE: Replacing a missing speaker - by KCMike - 07-14-2018, 07:03 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM

Who's Online

There are currently 5173 online users. [Complete List]
» 2 Member(s) | 5171 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me