Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith 9S232 sensitivity control
#5

LOL! Love Frank "Yeeesssss" Nelson!  John is right, Terry. That's exactly where the invisible #8 is hiding.

And Tony, you were right on the money. Look what I found on the RF coil:

   

There are actually two separate broken wires on the coil. This one is just the most visible. It may be hard to find the other stubs where these wires came off of. Will have to take the coil out tonight and get out the magnifying glass. I suppose I could just use one of the universal RF coils from AES, too?

How did you repair yours, Tony?

Greg V.
West Bend, WI
Member WARCI.org


Messages In This Thread
RE: Zenith 9S232 sensitivity control - by tbone - 06-18-2018, 12:05 PM
RE: Zenith 9S232 sensitivity control - by NostalgiaRadioTime - 06-18-2018, 06:45 PM
RE: Zenith 9S232 sensitivity control - by tbone - 06-18-2018, 09:18 PM
RE: Zenith 9S232 sensitivity control - by morzh - 06-18-2018, 10:17 PM
RE: Zenith 9S232 sensitivity control - by tbone - 06-19-2018, 05:01 AM
RE: Zenith 9S232 sensitivity control - by tbone - 06-19-2018, 08:14 PM
RE: Zenith 9S232 sensitivity control - by Arran - 06-20-2018, 02:57 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5198 online users. [Complete List]
» 2 Member(s) | 5196 Guest(s)
AvatarAvatar

>