Started my 41-295x restore.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Started my 41-295x restore.

nortonz
Member

Posts: 88
Threads: 17
Joined: May 2018
City: Hayden, ID

#13

06-20-2018, 11:45 PM

I had the grain filler on, then started the final Lacquer. everything looked pretty good, except the top, for some reason it bubbled up in a few places. not sure what caused that. I will have to re-strip the top, and start again.
Michael

Philco 41-295X 4 band radio.
I'm 67 years old, in north Idaho.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Started my 41-295x restore. - by nortonz - 05-11-2018, 01:19 AM

RE: Started my 41-295x restore. - by nortonz - 05-11-2018, 01:25 AM

RE: Started my 41-295x restore. - by nortonz - 05-11-2018, 05:11 PM

RE: Started my 41-295x restore. - by nortonz - 05-13-2018, 07:45 PM

RE: Started my 41-295x restore. - by Arran - 05-14-2018, 12:06 AM

RE: Started my 41-295x restore. - by nortonz - 05-14-2018, 01:22 PM

RE: Started my 41-295x restore. - by Arran - 05-14-2018, 09:15 PM

RE: Started my 41-295x restore. - by nortonz - 05-15-2018, 02:01 AM

RE: Started my 41-295x restore. - by nortonz - 05-15-2018, 03:37 PM

RE: Started my 41-295x restore. - by Ron Ramirez - 05-15-2018, 06:02 PM

RE: Started my 41-295x restore. - by rfeenstra - 05-16-2018, 12:57 AM

RE: Started my 41-295x restore. - by nortonz - 05-18-2018, 01:42 AM

RE: Started my 41-295x restore. - by nortonz - 06-20-2018, 11:45 PM

RE: Started my 41-295x restore. - by nortonz - 06-30-2018, 12:33 AM

RE: Started my 41-295x restore. - by 1MohrRadio - 12-29-2018, 07:28 AM

RE: Started my 41-295x restore. - by nortonz - 02-10-2019, 01:59 AM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM

Who's Online

There are currently 5025 online users. [Complete List]
» 1 Member(s) | 5024 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me