91D restoration

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

91D restoration

TexMac
Member

Posts: 12
Threads: 0
Joined: Jun 2010
City: Leesburg, TX

#17

07-18-2010, 01:31 PM

Personally, if it were my set, I would just detail clean the brass parts and preserve the patina since the case has just been cleaned and touched up with restor-a-finish. Just my 2 cents worth. I have a 91 and that is my plan, although I have to replace some veneer. My plan is to try to match the old veneer without refinishing it.

edit: oops. Did not realize there was a page 2 and Ron had already made my point better.

Ron Mc/

Find

« Next Oldest | Next Newest »

Messages In This Thread

91D restoration - by Guest - 07-02-2010, 03:37 PM

Re: 91D restoration - by Chuck Schwark - 07-03-2010, 12:27 PM

Re: 91D restoration - by Ron Ramirez - 07-04-2010, 07:38 AM

Re: 91D restoration - by Guest - 07-04-2010, 09:50 AM

Re: 91D restoration - by Ron Ramirez - 07-04-2010, 11:30 AM

Re: 91D restoration - by Guest - 07-04-2010, 12:23 PM

Re: 91D restoration - by Ron Ramirez - 07-04-2010, 12:45 PM

Re: 91D restoration - by Guest - 07-05-2010, 02:34 PM

Re: 91D restoration - by Ron Ramirez - 07-05-2010, 02:38 PM

Re: 91D restoration - by Guest - 07-11-2010, 01:59 PM

Re: 91D restoration - by Ron Ramirez - 07-11-2010, 03:46 PM

Re: 18D restoration - by Guest - 07-11-2010, 07:39 PM

Re: 91D restoration - by Ron Ramirez - 07-11-2010, 08:35 PM

Re: 18D restoration - by Guest - 07-12-2010, 01:14 PM

Re: 18D restoration - by Guest - 07-13-2010, 06:53 PM

Re: 91D restoration - by Ron Ramirez - 07-13-2010, 07:25 PM

Re: 91D restoration - by TexMac - 07-18-2010, 01:31 PM

Re: 18D restoration - by Guest - 07-20-2010, 09:49 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions. I'll write to the Henry Ford. That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me