Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 144H - How far to go?
#19

Hi Chas,
You might have a look at the back of the tuning capacitor sometimes the model # is stamped on it in ink.
Sorry the link I posted previously was dead try this: http://www.nostalgiaair.org/Resources/137/M0013137.htm
I'm about 99% sure it's a model 144 chassis

GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco 144H - How far to go? - by ChasBett - 07-11-2018, 08:56 PM
RE: How far to go? - by morzh - 07-11-2018, 09:21 PM
RE: How far to go? - by ChasBett - 07-11-2018, 09:40 PM
RE: How far to go? - by Electrothaumaturgist - 07-11-2018, 11:01 PM
RE: How far to go? - by Radioroslyn - 07-11-2018, 11:13 PM
RE: How far to go? - by morzh - 07-12-2018, 07:57 AM
RE: How far to go? - by KCMike - 07-12-2018, 10:24 AM
RE: How far to go? - by morzh - 07-12-2018, 10:44 AM
RE: Philco 144H - How far to go? - by ChasBett - 07-12-2018, 10:06 PM
RE: Philco 144H - How far to go? - by morzh - 07-12-2018, 10:38 PM
RE: Philco 144H - How far to go? - by Ron Ramirez - 07-13-2018, 06:07 AM
RE: Philco 144H - How far to go? - by morzh - 07-13-2018, 10:16 AM
RE: Philco 144H - How far to go? - by Ron Ramirez - 07-13-2018, 04:40 PM
RE: Philco 144H - How far to go? - by Phlogiston - 07-13-2018, 05:26 PM
RE: Philco 144H - How far to go? - by morzh - 07-13-2018, 07:55 PM
RE: Philco 144H - How far to go? - by Phlogiston - 07-13-2018, 08:53 PM
RE: Philco 144H - How far to go? - by ChasBett - 07-13-2018, 11:06 PM
RE: Philco 144H - How far to go? - by Radioroslyn - 07-13-2018, 11:11 PM
RE: Philco 144H - How far to go? - by Ron Ramirez - 07-14-2018, 07:38 AM
RE: Philco 144H - How far to go? - by RadioSvit - 10-01-2018, 10:43 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently no members online.

>