Replacing a missing speaker

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Replacing a missing speaker

Eric
Senior Member

Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA

#38

07-14-2018, 09:35 AM

Ok I found my mistake, Resistors R9 250k & R10 1meg are connected at a common point along with Cap C-22 what I did is swap the two other ends. They were located in a tight corner and not easily accessible but my volume is now good. I did the alignment and peaking of 1 & 2 IF's. Even the SW works after some cleaning of the rotary switch. I'll post a picture when I get it together.
Mike
I am curious in your pictures you show a resistor across the tone control mine did not have that nor do the prints show a resistor ?
Eric

Find

« Next Oldest | Next Newest »

Messages In This Thread

Replacing a missing speaker - by Eric - 06-08-2018, 08:56 AM

RE: Replacing a missing speaker - by KCMike - 06-08-2018, 10:02 AM

RE: Replacing a missing speaker - by Eric - 06-08-2018, 02:00 PM

RE: Replacing a missing speaker - by Radioroslyn - 06-08-2018, 02:56 PM

RE: Replacing a missing speaker - by KCMike - 06-08-2018, 03:03 PM

RE: Replacing a missing speaker - by Radioroslyn - 06-08-2018, 03:21 PM

RE: Replacing a missing speaker - by Arran - 06-09-2018, 02:41 AM

RE: Replacing a missing speaker - by Chas - 06-09-2018, 10:03 AM

RE: Replacing a missing speaker - by Eric - 06-10-2018, 02:40 PM

RE: Replacing a missing speaker - by Eric - 06-10-2018, 03:10 PM

RE: Replacing a missing speaker - by Arran - 06-11-2018, 02:24 AM

RE: Replacing a missing speaker - by Eric - 06-17-2018, 05:50 PM

RE: Replacing a missing speaker - by KCMike - 06-17-2018, 06:20 PM

RE: Replacing a missing speaker - by Eric - 06-17-2018, 07:45 PM

RE: Replacing a missing speaker - by KCMike - 06-17-2018, 07:58 PM

RE: Replacing a missing speaker - by Eric - 06-18-2018, 11:52 AM

RE: Replacing a missing speaker - by KCMike - 06-18-2018, 01:23 PM

RE: Replacing a missing speaker - by Radioroslyn - 06-18-2018, 01:34 PM

RE: Replacing a missing speaker - by Eric - 06-18-2018, 03:34 PM

RE: Replacing a missing speaker - by Eric - 06-18-2018, 04:00 PM

RE: Replacing a missing speaker - by KCMike - 06-18-2018, 05:34 PM

RE: Replacing a missing speaker - by Eric - 06-19-2018, 07:58 AM

RE: Replacing a missing speaker - by KCMike - 06-19-2018, 08:47 AM

RE: Replacing a missing speaker - by Eric - 06-19-2018, 09:50 AM

RE: Replacing a missing speaker - by Eric - 06-28-2018, 01:02 PM

RE: Replacing a missing speaker - by Radioroslyn - 06-28-2018, 04:44 PM

RE: Replacing a missing speaker - by Eric - 06-28-2018, 10:07 PM

RE: Replacing a missing speaker - by Radioroslyn - 06-29-2018, 03:12 PM

RE: Replacing a missing speaker - by Eric - 06-30-2018, 10:14 AM

RE: Replacing a missing speaker - by Radioroslyn - 06-30-2018, 11:47 AM

RE: Replacing a missing speaker - by Eric - 07-02-2018, 03:44 PM

RE: Replacing a missing speaker - by Eric - 07-10-2018, 02:56 PM

RE: Replacing a missing speaker - by Radioroslyn - 07-10-2018, 03:19 PM

RE: Replacing a missing speaker - by Eric - 07-10-2018, 05:06 PM

RE: Replacing a missing speaker - by Eric - 07-12-2018, 09:54 AM

RE: Replacing a missing speaker - by KCMike - 07-12-2018, 10:11 AM

RE: Replacing a missing speaker - by Eric - 07-12-2018, 04:18 PM

RE: Replacing a missing speaker - by Eric - 07-14-2018, 09:35 AM

RE: Replacing a missing speaker - by KCMike - 07-14-2018, 10:51 AM

RE: Replacing a missing speaker - by Eric - 07-14-2018, 05:01 PM

RE: Replacing a missing speaker - by KCMike - 07-14-2018, 07:03 PM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me