1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 38-4 Bezel Finish
Doug Houston
Silent Key
****
Posts: 337
Threads: 15
Joined: Nov 2005
City: Ortonville, MI
#2

07-28-2010, 10:53 PM
The bezwls for these sets were painnted in a sort of chocolate brown on the outer half of the bezel face, and the inner half of the bezel face was a sort of brush- satin natural brass finish...it's hard to describe. The brass carries over the inner surface that meets the glass.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 38-4 Bezel Finish - by Pol-Cat - 07-28-2010, 09:49 PM
Re: Philco 38-4 Bezel Finish - by Doug Houston - 07-28-2010, 10:53 PM
Re: Philco 38-4 Bezel Finish - by Pol-Cat - 07-30-2010, 11:01 PM
Re: Philco 38-4 Bezel Finish - by Ron Ramirez - 08-01-2010, 09:18 AM
Re: Philco 38-4 Bezel Finish - by Doug Houston - 08-02-2010, 10:51 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3441 online users. [Complete List]
» 2 Member(s) | 3439 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios