1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
AFC shorting switch 38-116
dixierat
Junior Member
**
Posts: 49
Threads: 8
Joined: Nov 2008
City: Baton Rouge, LA
#8

07-29-2010, 09:35 PM
I used a flat needle file from a set purchased from RS. A drop of deoxit on the file as suggested by Chuck is a good idea but I did'nt think of it.A burnishing tool would be a welcome addition to my tool drawer for use on the next sticky switch.No electronic background here so I don't know where to get one. If I get one I'll store it next to my hammer.
Find
« Next Oldest | Next Newest »


Messages In This Thread
AFC shorting switch 38-116 - by dixierat - 07-27-2010, 05:02 PM
Re: AFC shorting switch 38-116 - by Ron Ramirez - 07-28-2010, 10:45 AM
Re: AFC shorting switch 38-116 - by dixierat - 07-29-2010, 04:57 PM
Re: AFC shorting switch 38-116 - by Ron Ramirez - 07-29-2010, 06:01 PM
Re: AFC shorting switch 38-116 - by Chuck Schwark - 07-29-2010, 06:05 PM
Re: AFC shorting switch 38-116 - by Ron Ramirez - 07-29-2010, 07:16 PM
Re: AFC shorting switch 38-116 - by codefox1 - 07-29-2010, 09:13 PM
Re: AFC shorting switch 38-116 - by dixierat - 07-29-2010, 09:35 PM
Re: AFC shorting switch 38-116 - by Chuck Schwark - 07-30-2010, 11:37 AM
Re: AFC shorting switch 38-116 - by dixierat - 07-30-2010, 07:32 PM
Re: AFC shorting switch 38-116 - by Ron Ramirez - 07-31-2010, 07:11 AM
Re: AFC shorting switch 38-116 - by Chuck Schwark - 07-31-2010, 11:58 AM
Re: AFC shorting switch 38-116 - by codefox1 - 07-31-2010, 02:59 PM
Re: AFC shorting switch 38-116 - by BDM - 08-01-2010, 01:00 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration