1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Output transformers
Patrick
Senior Member
****
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
#1

07-19-2018, 04:15 PM
How critical is the primary impedence of the output xfmr? I'm talking specifically about 6V6 push-pull. If the wattage is similar, and the secondary impedence is correct, how much impact will variances in the primary have. The reason I'm asking is, I have a universal push-pull xfmr with variable primary from 1200-25000 Hz, but the schematic shows a 700Ω primary.
(This post was last modified: 07-19-2018, 04:16 PM by Patrick.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Output transformers - by Patrick - 07-19-2018, 04:15 PM
RE: Output transformers - by loepke72 - 07-19-2018, 04:53 PM
RE: Output transformers - by Patrick - 07-19-2018, 05:13 PM
RE: Output transformers - by loepke72 - 07-19-2018, 05:31 PM
RE: Output transformers - by Patrick - 07-19-2018, 05:37 PM
RE: Output transformers - by loepke72 - 07-19-2018, 06:01 PM
RE: Output transformers - by Patrick - 07-19-2018, 08:15 PM
RE: Output transformers - by codefox1 - 07-23-2018, 06:37 PM
RE: Output transformers - by Stan the Man - 08-24-2018, 01:17 PM
RE: Output transformers - by Patrick - 08-24-2018, 02:15 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 5412 online users. [Complete List]
» 1 Member(s) | 5411 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration