Atwater Kent 246

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Atwater Kent 246

dkoczur
Junior Member

Posts: 12
Threads: 3
Joined: Jan 2014
City: Burke Va

08-07-2018, 08:44 AM

I am trying to rebuild an Atwater Kent 246 cabinet. I need a couple of dimensions if anyone could provide them.

Inside cabinet dimension from one cabinet wall to the opposite wall (not including molding or strengthen piece)
Inside cabinet dimension from base to top of cabinet at centerline. (not including molding)
Depth of cabinet from front to back edge of base.

If possible, a tracing of the cabinet curve. If you can provide this, let me know whether it was from the outside of the molding or the inside
(if you do the back) or if it is from the front panel.

Thanks for any help you can provide.

Dan Koczur

Find

« Next Oldest | Next Newest »

Messages In This Thread

Atwater Kent 246 - by dkoczur - 08-07-2018, 08:44 AM

RE: Atwater Kent 246 - by Eliot Ness - 08-07-2018, 10:34 AM

RE: Atwater Kent 246 - by dkoczur - 08-08-2018, 11:50 AM

RE: Atwater Kent 246 - by Eliot Ness - 08-08-2018, 12:02 PM

RE: Atwater Kent 246 - by dkoczur - 08-09-2018, 10:38 AM

RE: Atwater Kent 246 - by Eliot Ness - 08-18-2018, 10:34 AM

RE: Atwater Kent 246 - by dkoczur - 08-18-2018, 07:59 PM

RE: Atwater Kent 246 - by Eliot Ness - 09-05-2018, 11:26 AM

RE: Atwater Kent 246 - by dkoczur - 09-05-2018, 11:58 AM

RE: Atwater Kent 246 - by dkoczur - 11-03-2018, 09:25 AM

RE: Atwater Kent 246 - by Eliot Ness - 11-20-2018, 09:09 PM

RE: Atwater Kent 246 - by dkoczur - 11-21-2018, 03:09 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 6062 online users. [Complete List]
» 1 Member(s) | 6061 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me