Philco 38-7

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 38-7

PhilcoPhan1936
Jeff W.

Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro State, Province, Country: AR

#20

08-14-2018, 04:35 PM

(08-14-2018, 06:25 AM)Ron Ramirez Wrote: When (29) is closed, the audio is shorted to ground.

Try disconnecting one end of the wire going to (29) and try again.

Still deaf as a post. Icon_thumbdown

Printing up a fresh schematic and going over every connection and part with a fine tooth comb..... Icon_crazy

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco 38-7 - by PhilcoPhan1936 - 08-09-2018, 02:50 PM

RE: Philco 38-7 - by Olskuul - 08-09-2018, 05:10 PM

RE: Philco 38-7 - by Radioroslyn - 08-09-2018, 06:08 PM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-09-2018, 09:47 PM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-10-2018, 05:40 PM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-10-2018, 06:09 PM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-13-2018, 05:03 PM

RE: Philco 38-7 - by Radioroslyn - 08-13-2018, 05:30 PM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-13-2018, 05:48 PM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-13-2018, 06:11 PM

RE: Philco 38-7 - by Radioroslyn - 08-13-2018, 06:55 PM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-13-2018, 07:23 PM

RE: Philco 38-7 - by Radioroslyn - 08-13-2018, 09:22 PM

RE: Philco 38-7 - by Arran - 08-13-2018, 09:38 PM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-14-2018, 04:17 AM

RE: Philco 38-7 - by Ron Ramirez - 08-14-2018, 06:25 AM

RE: Philco 38-7 - by Radioroslyn - 08-14-2018, 08:28 AM

RE: Philco 38-7 - by cpollock - 08-14-2018, 12:30 PM

RE: Philco 38-7 - by Radioroslyn - 08-14-2018, 01:01 PM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-14-2018, 04:35 PM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-14-2018, 05:40 PM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-14-2018, 10:49 PM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-27-2018, 03:34 AM

RE: Philco 38-7 - by PhilcoPhan1936 - 08-27-2018, 07:54 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM
My Philco 37-116 Restore
Are you measuring relative to the centertap or the GND?morzh — 11:57 PM
Philco 610B oscillator wiring
Still not clear on the wiring interface between the 6A7 and oscillator. After refering to the available schematics and s...Tubester — 07:18 PM
Refinishing Ideas
My 37-116 code 121 is the best sounding radio i have...a daily driver. Since we are talking about "changes". ...poulsbobill — 07:18 PM
My Philco 37-116 Restore
Hello, I finally got brave enough to take the cans off the Expander Unit. Got the grid cap wires replaced and back toget...dconant — 06:50 PM
Zenith H725
I got into the first AM IF can today, and found its mica was cracked. Amazing that it was still working. This one makes ...EdHolland — 06:10 PM
Philco model #20
AHH HA , I got it and can’t thank you fellows enough , when I changed the capacitors I took the advice and did not unsol...onlyrick — 02:24 PM
Zenith H725
Hello Ed, yes, I like letting projects run for few days to make sure they don't start acting up . Sincerely Richardradiorich — 01:03 PM
Philco 46-480 Electronic Restoration
I am almost finished with this restoration. All which remains is the power transformer. I cleaned it up some time ago, b...jrblasde — 12:41 PM

Who's Online

There are currently 998 online users. [Complete List]
» 2 Member(s) | 996 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me