Model 90 lowboy speaker rewiring question

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Model 90 lowboy speaker rewiring question

WyTex
Senior Member

Posts: 289
Threads: 42
Joined: Jan 2014
City: Jeffersonville State, Province, Country: PA

08-21-2018, 04:23 PM

The bakelite plug on my set cannot be re-wired to the pins without separating the plug. The two halves are sandwiched together with no space. I was assuming the rivets needed to be drilled or perhaps pried up as Ed suggested. There isn't any access to the back end of the pins. Just want to make sure I'm doing this correctly and not hack it up.

Thanks again.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Model 90 lowboy speaker rewiring question - by WyTex - 08-21-2018, 11:50 AM

RE: Model 90 lowboy speaker rewiring question - by EdHolland - 08-21-2018, 12:28 PM

RE: Model 90 lowboy speaker rewiring question - by morzh - 08-21-2018, 01:09 PM

RE: Model 90 lowboy speaker rewiring question - by WyTex - 08-21-2018, 01:42 PM

RE: Model 90 lowboy speaker rewiring question - by morzh - 08-21-2018, 02:31 PM

RE: Model 90 lowboy speaker rewiring question - by WyTex - 08-21-2018, 03:09 PM

RE: Model 90 lowboy speaker rewiring question - by morzh - 08-21-2018, 03:12 PM

RE: Model 90 lowboy speaker rewiring question - by WyTex - 08-21-2018, 04:23 PM

RE: Model 90 lowboy speaker rewiring question - by KCMike - 08-21-2018, 06:25 PM

RE: Model 90 lowboy speaker rewiring question - by EdHolland - 08-21-2018, 06:28 PM

RE: Model 90 lowboy speaker rewiring question - by Steve Davis - 08-21-2018, 07:22 PM

RE: Model 90 lowboy speaker rewiring question - by morzh - 08-21-2018, 11:25 PM

RE: Model 90 lowboy speaker rewiring question - by WyTex - 08-22-2018, 09:12 AM

RE: Model 90 lowboy speaker rewiring question - by WyTex - 08-23-2018, 02:51 PM

RE: Model 90 lowboy speaker rewiring question - by morzh - 08-23-2018, 03:15 PM

RE: Model 90 lowboy speaker rewiring question - by WyTex - 08-23-2018, 03:29 PM

View a Printable Version

Users browsing this thread:

Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

Who's Online

There are currently 1041 online users. [Complete List]
» 3 Member(s) | 1038 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me