1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
6287-R Block condensor
Brian_w5ami
Junior Member
**
Posts: 19
Threads: 4
Joined: May 2018
City: Vilonia, Arkansas
#4

08-31-2018, 06:42 PM
Another question on this are the internal connections.  What lugs are these two 0.15 caps connected to?  This block is only specified as a single .25, but there are three lugs and all of them are used as a connection point for something.  There is no reference on the schematic of using a single cap inside this block.  Is the middle lug a dummy?  I do not see a wire coming up through the rivet on the middle lug, so maybe it is.

Are there any pre 1936 catalogs out there that have these discontinued blocks so I won't have to keep asking about their specs?
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
6287-R Block condensor - by Brian_w5ami - 08-31-2018, 12:51 PM
RE: 6287-R Block condensor - by Radioroslyn - 08-31-2018, 03:13 PM
RE: 6287-R Block condensor - by Brian_w5ami - 08-31-2018, 05:29 PM
RE: 6287-R Block condensor - by Brian_w5ami - 08-31-2018, 06:42 PM
RE: 6287-R Block condensor - by PhilcoPhan1936 - 08-31-2018, 08:43 PM
RE: 6287-R Block condensor - by Ron Ramirez - 09-01-2018, 12:58 PM
RE: 6287-R Block condensor - by Brian_w5ami - 09-01-2018, 01:04 PM
RE: 6287-R Block condensor - by PhilcoPhan1936 - 09-01-2018, 01:09 PM
RE: 6287-R Block condensor - by gary rabbitt - 10-11-2018, 11:35 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM

[-]
Who's Online
There are currently 1016 online users. [Complete List]
» 1 Member(s) | 1015 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration